Volkswagen Golf Service & Repair Manual
- General body repairs, exterior
- Body front
- Bonnet. flaps.cab. central loking
- Front door, central locking
- Rear door, sliding door, wing doors, central locking
- Sliding roof
- Bumper
- Glazing/window mechanism
- Exterior equipment
- General body repairs, interior
- Technical data
- Interion equipment
- Pasanger protection
- Trim, noise insulation
- Seat frames
- Seat padding, covers
- General information, paint
- Vechile- specific paint information
- Explanation of symbols
- Paintwork structure
- Areas exposed to stone chipping
- Masking areas
- Seam seals
- Undercoating
- Cavity sealing
- Heating, air conditioning
- Auxiliary heater
- Air conditioning system with refrigerant R134a
- General notes on air conditioning systems
- General information on refrigerant circuit
- Statutory texts and instructions
- Refrigerant circuit
- Working with the air conditioner service station
- Detecting leaks in refrigerant circuit
- Clearing refrigerant circuit of contaminants
- Complaints
- Connecting air conditioner service station
- Checking pressures on vehicles
- Renewing components
- Testing equipment and tools
- 7- speed dual clutch gearbox 0CW
- Technical data
- Clutch, control
- Gearbox mechanism, operation, contruction, diff
- Gearbox. mechanics, gears, shafts, internal operation
- Final drive, differential, differential lock
- 4- cylinder injection engine(1.4 1 direct inction. turbocharger)
- Technical data
- Engine assy, cylinder blook, crankcase
- Enginecrankshaft group, pistons
- Engine cylinder head, valve gear
- Engine lubrication
- Engine cooling
- Exhaust turbocharger, g-charger
- Mixture preparation system, electronic inj., Gas
- Exhaus system
- Ignition system, glow plug system
- Fuel supply system - Petrol engines
- Running gear, axles, steering
- Technical data
- Front suspension, drive shafts
- Rear suspension, drive shaft
- Self- levelling air spring system
- Wheels, tyres, axle align
- Steering
- Brake system
- Wheels and Tyres guide
- Guide for using trailers
- Wheels and Tyres Guide - General Information
- Specifications for converting wheel and tyre combinations, documents
- Handling problems
- Evaluating tyres
- Tyre wear
- Overview of components
- Fitting tyre
- Fitting wheels
- Information on tyres
- Information on wheel rims
- Tyre pressure sensor
- Tyre sealant
- Wheel bolts
- Snow chains
- Temporary spare wheels
- Brake system (hybrid)
- Electrical system
- Technical data
- Starter- current supply- CC
- Instruments, GCI
- Windscreen wipe/ wash system
- Lights, lamps, switches outside
- Lights, lamps, switches inside, anti- theft system
- Wiring
- Communication
- Electrical system, general information
Driving notes on towing
First read and observe the introductory information
and safety warningsTowing requires some experience, especially when using
a tow rope. Both drivers should be familiar with the technique require ...
Other materials:
Removing and installing rear lid seal
In the factory a sealant is applied to the rear lid seal, the seal is fitted
to the body flange and then rolled on.
Note
When the seal is removed, the sealant on the inside of the seal will
be spread and the flanks will be bent out slightly. If the seal is then
refitted, sealing and fir ...
Balancing wheel, balancing wheel with finish balancer
Note
Before working with a finish balancer, the mechanic needs to
have been instructed by the manufacturer of the balancer.
To balance the wheels, set the wheels of the driven axle on
the sensor platforms. On front-w ...
Emptying fuel tank with fuel pump intact, engine code CWVA
Special tools and workshop equipment required
Removal wedge -3409-
Remote control -V.A.G 1348/3A-
Test instrument adapter/DSO (5-pin) -VAS 5565-
Fuel extractor -VAS 5190-
Fuel extractor -VAS 5190 A- for ...
