Volkswagen Golf Service & Repair Manual: Wax-based underseal -D 316 000 A1
| Wax-based underseal -D 316 000 A1- |
| Wax underseal -D 316 000 A1- offers excellent long-term
underbody corrosion protection. |
| Wax underseal is based on a solvent-free, oxidative-drying
system and offers excellent underbody corrosion protection. |
| This corrosion protection is the result of very good
adhesion to metal surfaces at both very low and high
temperatures. |
| The product creates a light-brown, elastic coating which is
firm to the touch. |
| It is not necessary to raise the temperature to produce a
film coating. |
| Technical data sheet, wax underseal -D 316 000 A1- |
| The material is used primarily in automotive applications. |
| Ensure that the substrates are dry. |
| The ready-to-use product is applied by brush at a material
temperature between 20 and 35 °C. |
| When required by the application method, the material can be
gently heated to maximum 45 °C directly () before application. |
| The oxidative curing product may already develop a skin on
the surface after only a short time. This has no influence on
its anti-corrosion protection or other properties |
| Active ingredient content: 100% |
| Excellent long-term anti-corrosion protection |
| Low-temperature flexibility |
 Note
| Before using, read the safety measures and recommendations
in the safety data sheet. |
| Even for products which are not required by law to be
labelled, the usual safety measures for chemical products must
be observed. |
| The surfaces to be treated must be dry and free of grease or
dust. |
| Bring wax-based underseal to application temperature
(20-35 °C). |
| Apply material to body parts which are to be protected and
spread with a brush. |
|
|
|
| Base |
Mixture of anti-corrosion
additives on sulfonate basis, alkyd resin, special mineral oil
raffinates, pigments, thickeners, drying accelerators and fluorescent
pigments. |
| Form and colour as
supplied |
light-brown, viscous liquid |
| Rheomat viscosity |
1850 ± 350 mPas (PP50
system, d= 760 1/s) |
| Density at 15 °C DIN EN
ISO 12185 |
0.995 ± 0.015 g/ml |
| Solids content |
99 ± 1 % |
| Flashpoint DIN EN ISO
2719 |
Approx. 150 °C |
| Recommended coat
thicknesses |
100-400 µm |
| Working temperature |
+20 °C to +35 °C |
| Storage |
Approx. 12 months at
temperatures between +10 °C and 30 °C |
| Container |
310 ml |
Designation:
Wax-based underseal -D 316 D38 A2-
Issued 04.2009
Product description
...
Designation:
Spray wax (spraying wax) -D 322 100 M2-
Issued 01.2011
Product description
...
Other materials:
Removing and installing side defroster vent
Note
Removal and installation is described for the side defroster
vent on driver side. Follow same instructions for the front
passenger side as appropriate.
Special tools and workshop equipment
required
&nb ...
Removing and installing reversing camera -R189-
Reversing camera and swivel motor are each installed in
individual housings together in swivel badge of rear lid. To
remove camera housing, remove first both components together
with swivel badge from rear lid. Afterwards, camera housing
together with sw ...
Removing and installing fuel rail
Removing
The fuel system is under high pressure.Risk of injury due to fuel which
may spurt out.Release high pressure.
→ Chapter
Risk of functional impairment due to soiling
→ Chapter.
...
© 2016-2026 Copyright www.vwgolf.org
Wax-based underseal -D 316 D38 A2
Spray wax (spraying wax) -D 322 100 M2