Volkswagen Golf Service & Repair Manual: Texture additive

Volkswagen Golf Service & Repair Manual / General information, paint / Genuine products / Additional materials / Texture additive

Designation:

Fine texture additive -ALN 775 108-

Issued 04.2013

Product description

The fine texture additive -ALN 775 108- is designed to be added to 2-pack HS top coats. The respective top coat is then converted into a texture paint

that can be used for treating plastic vehicle parts.

Technical data sheet

Substrate

Suitable substrates:

Hardened, well-preserved and lightly sanded old or factory finish.

Plastic parts coated with primer or surfacer.

Note

For plastic parts, see "The VW/Audi painting system for plastic parts" (data sheet no. 5.74).

Substrate pre-treatment:

–	Thoroughly clean with silicone remover -LVM 020 000 A5- or slow-drying silicone remover -LVM 020 100 A5-.

Texture additive

–	Dry sand using orbital sander (P400 to P500 grade) and dust collector.

Texture additive

–	Alternatively, wet sand with P800-grain sandpaper.

Texture additive

–	Before recoating, use a suitable cleaning agent to ensure a clean surface free of residues.

Application

Texture additive

Mixing ratio

Mixing ratio 1:1 by volume with 2-pack HS top coat:

–	Then mix this 4:1 by volume with a suitable 2-pack VHS hardener.

See technical data sheet for 2-pack VHS hardener → Chapter.

Thinner:

2-pack thinner, special -LVM 009 200 A2/A5-

2-pack thinner, slow-drying -LVM 009 300 A2-

Texture additive

Application time/pot life:

–	Mixed for spraying, 90 to 100 minutes at +20°C

Texture additive

Method of application: “spray”.

Texture additive

–	Application viscosity 4 mm, +20 °C, DIN 53211

–	The application viscosity at +20 °C is the “compliant” and “HVLP” mixing viscosity.

Texture additive

–	Add 15 % thinner at +20 °C material temperature.

Texture additive

–	Adjust spray nozzle following manufacturer's instructions to 1.3-1.4 mm for “compliancy”.

–	Adjust spray nozzle following manufacturer's instructions to 1.3-1.5 mm for “HVLP”.

–	Adjust spray pressure following manufacturer's instructions to 2.0-2.5 bar for “compliancy”.

–	Adjust atomising pressure following manufacturer's instructions to 0.7 bar for “HVLP”.

Texture additive

–	Two spray passes (with intermediate flash-off time of 5 to 10 minutes) are necessary to achieve the recommended dry-film thickness of 50-60 µm.

Note

It is not necessary to add the elastic additive -ALZ 011 001-.

The fine texture additive -ALN 775 108- is only suitable for use on add-on parts (e.g. bumpers or spoilers).

Various effects can be created using different spraying techniques and layer thicknesses.

The fine texture additive -ALN 775 108- is thixotropic and becomes liquid when stirred well.

Texture additive

Drying

Air drying at +20 °C ambient temperature:

Dust dry in 30-50 minutes

Dry for assembly in 4-6 hours

Dry overnight

Texture additive

Final flash-off time with force drying is at least 5-10 minutes.

Texture additive

Force drying at +60 °C material temperature in 30-40 minutes.

Texture additive

The final flash-off time with infrared drying is 5 minutes.

Texture additive

Infrared drying with short-wave radiant heater, 10-15 minutes and medium-wave radiant heater, 15-20 minutes.

Texture additive

Personal protective equipment:

Adhere to the safety data sheet.

Wear personal protective equipment during application.

Data

Texture additive

Viscosity as supplied	Thixotropic
Flash point:	Above +23 °C
VOC content: 2004/42/IIB(e)(840)600	The EU limit value for this product (product category IIB.e) in ready-to-spray form is max. 840 g/l of volatile organic compounds. The VOC content of this product in ready-to-spray form is max. 600 g/l.

Storage

The guaranteed shelf life is 24 months from date of production. May be used until the date stated on the label at latest if stored in sealed original containers at +20 °C.

Texture additive

Blending additive for Aquaplus

Designation:

Blending additive for Aquaplus -LVM 030 000 A2-

Note

For information on preparing and applying the blending additive for Aquaplus -LVM 030 000 A2-, refer to chapter → Chapter „Aquaplus blending system“.

Matting additive -LVM 769 810 A2

Designation: Matting additive -LVM 769 810 A2- Issued 10.2014 Product description ...

Additive for Aqua Premium

Designation: Additive for Aqua premium -LVM 035 200 A2/A3- Additive for Aqua premium -LVM 035 300 A1- ...

Other materials:

Removing and installing water drain hoses
Note In models for “NAR” market, the left rear water drain hose ends in the left wheel housing. Removing front water drain hose – Remove A-pillar trim → General body repairs, interior; Rep. gr.70. ...

Removing and installing decoupler pulley with freewheel‏
General description There are different versions of decoupler pulleys with freewheel‏. Before removing the decoupler pulley with freewheel, it must be determined which special tool must be used. ...

Changing bulbs in the front bumper
Fig. 236 In the front right wheel housing liner: changing a bulb in the headlight First read and observe the introductory information and safety warningsBefore changing the bulb in the left-hand headlight, turn the steering wheel all the way to the right. Before changing the bulb in the righ ...