Volkswagen Golf Service & Repair Manual: Blender

Volkswagen Golf Service & Repair Manual / General information, paint / Genuine products / Clear coats / Blender

Designation:

Blender -LVE 013 100 A2-

Issued 10.2012

Product description

Blender was developed to guarantee easy blending-in of 2-pack clear coats and top coats.

Properties:

Easy to use in its pure form

Good wetting on all substrates

Very fine fade-out to the old finish

Technical data sheet

Preparation

Base coat application:

Keep the surfacer area as small as possible.

Overpaint with waterborne base coat until surfacer area is fully hidden (overlapping coats).

Blending system for 2-pack clear coats

Mixing ratio with 2-pack clear coat:

Mix according to the technical data sheet for the clear coat → Chapter.

Blender

Paintwork:

–	Overpaint waterborne base coat with adjusted clear coat, overlapping the coats.

Blender

Blending in:

–	Apply pure blender -LVE 013 100 A2- to the blending area within the sanded area.

Blender

Blending system for 2-pack top coats

Mixing ratio with 2-pack top coat:

Mix according to the technical data sheet for the 2-pack top coat → Chapter.

Blender

Paintwork:

–	Recoat until surfacer area is fully hidden, overlapping the coats.

Blender

Blending in:

–	Apply pure blender -LVE 013 100 A2- to the blending area within the sanded area.

Blender

Polishing blending areas

Air drying at +20 °C ambient temperature:

Allow blending areas to dry overnight before polishing

Blender

Final flash-off time with force drying is at least 5-10 minutes.

Blender

Force drying at +60 °C material temperature in 30 minutes.

–	The blending areas may then be polished after cooling for one hour at +20 °C ambient temperature.

Blender

Final flash-off time with infrared drying is at least 5-10 minutes.

Blender

Infrared drying with short-wave radiant heater, 10 minutes.

–	The blending areas may then be polished after cooling for one hour at +20 °C ambient temperature.

Note

Polish the blending areas with fine polishing paste by hand or with a polishing machine.

Finally treat the surface with high-gloss sealer.

Blender

Personal protective equipment:

Adhere to the safety data sheet.

Wear personal protective equipment during application.

Data

Blender

Flash point:

+20 °C

Storage

The guaranteed shelf life is 60 months from date of production. May be used until the date stated on the label at latest if stored in sealed original containers at +20 °C.

Blender

2-pack HS Performance clear coat

Designation: 2-pack HS Performance clear coat -LZK 769 K06 A5- Issued 08.2012 Product description ...

Hardener

...

Other materials:

Spray wax (spraying wax) -D 322 100 M2
Designation: Spray wax (spraying wax) -D 322 100 M2- Issued 01.2011 Product description Spray wax (spraying wax) -D 322 100 M2- is a long-term anti-corrosion agent. The produ ...

Removing and installing camshaft control valve 1 -N205- and exhaust camshaft control valve 1 -N318-
Note On engines with codes CMBA, CPVA, CXSA, CZCA and CPVB, only camshaft control valve 1 -N205- is installed. Removing Inlet camshaft control valve 1 -N205- – Disconnect ele ...

Overview of fitting locations - components not located in passenger compartment, Golf Variant LHD
1 - Exhaust ventilation for passenger compartment Checking → Chapter Removing and installing → Chapter 2 - Humidity sender for air conditioning system -G260- Check v ...