Volkswagen Golf Service & Repair Manual: Wax-based underseal -D 316 000 A1

Volkswagen Golf Service & Repair Manual / General information, paint / Genuine products / Wax-based underseal / Wax-based underseal -D 316 000 A1

Designation:

Wax-based underseal -D 316 000 A1-

Issued 01.2008

Product description

Wax underseal -D 316 000 A1- offers excellent long-term underbody corrosion protection.

Wax underseal is based on a solvent-free, oxidative-drying system and offers excellent underbody corrosion protection.

This corrosion protection is the result of very good adhesion to metal surfaces at both very low and high temperatures.

The product creates a light-brown, elastic coating which is firm to the touch.

It is not necessary to raise the temperature to produce a film coating.

Technical data sheet, wax underseal -D 316 000 A1-

Application

The material is used primarily in automotive applications.

Ensure that the substrates are dry.

The ready-to-use product is applied by brush at a material temperature between 20 and 35 °C.

When required by the application method, the material can be gently heated to maximum 45 °C directly () before application.

The oxidative curing product may already develop a skin on the surface after only a short time. This has no influence on its anti-corrosion protection or other properties

Properties

Solvent-free

Active ingredient content: 100%

Excellent long-term anti-corrosion protection

Good adhesion

Low tendency to drip

Low-temperature flexibility

Long storage life

Note

Before using, read the safety measures and recommendations in the safety data sheet.

Even for products which are not required by law to be labelled, the usual safety measures for chemical products must be observed.

Application

The surfaces to be treated must be dry and free of grease or dust.

Bring wax-based underseal to application temperature (20-35 °C).

Apply material to body parts which are to be protected and spread with a brush.

Technical data

Base	Mixture of anti-corrosion additives on sulfonate basis, alkyd resin, special mineral oil raffinates, pigments, thickeners, drying accelerators and fluorescent pigments.
Form and colour as supplied	light-brown, viscous liquid
Rheomat viscosity	1850 ± 350 mPas (PP50 system, d= 760 1/s)
Density at 15 °C DIN EN ISO 12185	0.995 ± 0.015 g/ml
Solids content	99 ± 1 %
Flashpoint DIN EN ISO 2719	Approx. 150 °C
Recommended coat thicknesses	100-400 µm
Working temperature	+20 °C to +35 °C
Storage	Approx. 12 months at temperatures between +10 °C and 30 °C
Container	310 ml

Wax-based underseal -D 316 D38 A2

Designation: Wax-based underseal -D 316 D38 A2- Issued 04.2009 Product description ...

Spray wax (spraying wax) -D 322 100 M2

Designation: Spray wax (spraying wax) -D 322 100 M2- Issued 01.2011 Product description ...

Other materials:

Overview of the driver door
Fig. 4 Overview of the controls in the driver door (left-hand drive vehicles) The controls are mirrored for right-hand drive vehicles Key for : Door release lever Central locking buttons for locking and unlocking the vehicle – Switch for adjusting the exterior ...

Introduction
This chapter contains information on the following subjects: → Preparing for a journey and driving safely → Driving abroad → Driving through water on roads Depending on where the vehicle is used, it could be a good idea to have an engine and transmiss ...

Removing front seat if seat longitudinal adjustment motor -V28-/-V31- is defective
Checking seat longitudinal adjustment motor -V28-/-V31- – Move front seat to highest position. Note To prevent unnecessary repair costs check seat longitudinal adjustment motor -V28-/-V31- prior to ...