Volkswagen Golf Service & Repair Manual: Silicone remover -LLS MAX 007

Volkswagen Golf Service & Repair Manual / General information, paint / Genuine products / SprayMax System / Silicone remover -LLS MAX 007

Designation:

Silicone remover -LLS MAX 007-

Issued 10.2008

Product description

The silicone remover -LLS MAX 007- is a waterborne cleaning agent, rich in active ingredients and with a reduced solvent content. The raw material basis is a combination of specific solvents.

Properties:

Aerosol formulation made for this specific product for easy application.

Constant atomisation pressure.

Finest aerosol dispersion.

Very high coverage.

First-class painting results.

Great cleaning and degreasing action.

Reinforces adhesion properties.

Very high coverage.

Uniform distribution.

Technical data sheet

Application

Recommended for:

Utility for parts painting and spot repairs.

Perfectly suitable for pre-treating surfaces to be coated with Aquabase Plus waterborne base coats.

Suitable substrates:

Painted or unpainted metal, plastic or glass surfaces (old or factory paint jobs) which have been coated with a primer or surfacer.

Substrate	Suitability
Surfaces coated with primer or surfacer	+++
Old or factory paint jobs	+++
Plastic parts	+++
Metal/glass	+++

Properties:

Non-aggressive to painted surfaces.

Removes all kinds of silicone and is an ideal cleaner of dirt and soot.

Removes body cavity sealant or wax.

Removes resin-hardened grease residues, such as on door hinges.

Eliminates oil and grease residues.

Ideal for dissolving tar.

Removes adhesive residues, such as from labels.

Application

Note

Protective garments and equipment in accordance with work safety regulations must be worn:

Respirator mask, type A2/P2.

Protective gloves (e.g. latex or nitrile).

Method of application: “spray”.

–	Apply one light spray pass of silicone remover right before applying the subsequent paint coat, and immediately wipe dry with a clean, dry cloth.

–	Do not allow the silicone remover to evaporate from the surface. Only small areas may be treated simultaneously.

–	Heavily soiled parts must be cleaned twice.

–	Replace clothes often - do not use dirty clothes.

Note

After any interruption of the spray operation, hold the aerosol upside down, and press the spray button until the valve is empty.

Caution

Protective garments and equipment in accordance with work safety regulations must be worn.

Observe safety information sheets as well as warnings on the label of the spray can.

After fully emptying the spray can, dispose of as recycling material

Data

Silicone remover -LLS MAX 007

Solids content:	0 %
Coverage:	Approx. 0.75 to 1.0 mІ per aerosol.
Degree of gloss:	Not applicable
VOC content:	620 g/l ± 248 g per aerosol.

Storage

The guaranteed shelf life is 36 months from date of production. May be used until the date stated on the label at latest if stored in sealed original containers at +20 °C.

Silicone remover -LLS MAX 007

2-pack wash primer

Designation: 2-pack wash primer -LLS MAX 230 M1-, olive-green (250 ml) Issued 12.2013 Product desc ...

Slow-drying silicone remover -LLS MAX 008

Designation: Slow-drying silicone remover -LLS MAX 008- Issued 10.2008 Product description ...

Other materials:

Overview of fitting locations - rear keyless entry system, LHD vehicles
1 - Luggage compartment aerial for entry and start system -R137- Removing and installing → Chapter 2 - Interface for entry and start system -J965- Removing and installing → Chapter ...

Infrared heater -VAS 6874
Designation: Infrared heater -VAS 6874- Product description: The infrared heater is used to dry putty, filler, base coat, top coat and clear coat on vertical surfaces with 2 timers for flashi ...

Removing and installing centre console trim in footwell
Note Removal and installation is described for the centre console trim in footwell on driver side. Follow same instructions for the front passenger side as appropriate. Special tools and workshop equipment required ...