Volkswagen Golf Service & Repair Manual: Removing automatic distance control unit from and installing on retaining
plate, variant 1
| Adjusting adjustment screws:
→ Anchor |
| Renewing clips on adaptive cruise control unit -J428-:
→ Anchor |
| Special tools and workshop equipment
required |
| Calliper square -VAS 6335- |
| – |
Remove adaptive cruise control unit -J428-
→ Chapter. |
|
|
|
| – |
Turn quick-release fasteners -2-
in -direction of arrow-. |
| – |
Remove retaining plate -3- from
adaptive cruise control unit -J428--4-. |
| – |
Pull quick-release fasteners -2-
off adjustment screws -1-. |
| Install in the reverse order of removal, observing the
following: |
 Note
| Renew quick-release fasteners -2-. |
| The adjustment screws -1- in
the automatic distance control unit -J428- are preset. Correct
the adjustment as required
→ Anchor. |
| If studs -1- have been
unscrewed, clips on the adaptive cruise control unit -J428- need
to be renewed
→ Anchor. |
|
|
|
| – |
Carefully press new quick-release fasteners
-4- onto studs
-2-. |
| – |
Fit retaining plate -3- to
adaptive cruise control unit -J428--1-. |
| – |
Engage quick-release catches -4-
on retaining plate -3- in
-direction of arrow- as far as
stop. |
| – |
Install adaptive cruise control unit -J428-
→ Chapter. |
| Adjusting adjustment screws |
|
|
|
| – |
Place adaptive cruise control unit -J428- on a soft and
clean surface. |
| – |
Using digital calliper -VAS 6335-, measure setting
-a- of all adjustment screws and
correct, if necessary. |
| Renewing clips on adaptive cruise
control unit -J428- |
|
|
|
| – |
Unscrew adjustment screw -1-
using suitable tool -2-. |
|
|
|
| – |
Set screwdriver -A- between
retaining hook and housing. |
| – |
Bend retaining hooks with the screwdriver one after the
other towards the centre until they audibly break off. |
| – |
To prevent broken hooks from becoming caught in the housing,
remove them from inside clip using long-nose pliers
-B-. |
|
|
|
| – |
Insert new clip -A- into hole
in housing, and press it on by hand until it engages audibly
-arrow-. The lugs on the clip must
sit correctly in the recesses. |
| – |
Screw in adjustment screw -B--arrows-.
Adjustment screw must be parallel to bore and correctly aligned
with clip. |
| – |
Adjust adjustment screws
→ Anchor. |
| – |
Repeat this process if necessary at other clips. |
| – |
Install retaining plate for adaptive cruise control unit
-J428-
→ Anchor. |
|
|
|
Note
If the automatic distance control unit -J428- is renewed,
start the respective function → Vehicle
diagnostic tester.
...
Note
If the automatic distance control unit -J428- is renewed,
start the respective function → Vehicle
diagnostic tester.
...
Other materials:
Cleaning and changing windscreen wiper blades
Fig. 198 Changing the windscreen wiper
blades
Fig. 199 Changing the rear window wiper
blade
First read and observe the introductory information
and safety warnings The factory-fitted windscreen wiper blades are coated
with graphite. The graphite coating ensures that the windscreen wipe ...
Removing and installing window regulator
Special tools and workshop equipment
required
Note
Removal and installation are described only for the left
window regulator. Removal and installa ...
1-pack anti-corrosion wash primer
Designation:
1-pack anti-corrosion wash primer -ALN 002 003 10-
Issued 06/2011
Product description
1-pack anti-corrosion primer is a zinc chromate-free
one-pack produc ...
© 2016-2024 Copyright www.vwgolf.org
Removing and installing automatic distance control unit, variant 1
Removing automatic distance control unit from and installing on retaining
plate, variant 2