Volkswagen Golf Service & Repair Manual: Removing and installing wheel bearing unit, torsion beam axle

Volkswagen Golf Service & Repair Manual / Running gear, axles, steering / Rear suspension, drive shaft / Wheel bearing assembly, trailing arm / Removing and installing wheel bearing unit, torsion beam axle

Removing and installing wheel bearing unit, torsion beam axle

Special tools and workshop equipment required

Fitting sleeve -3241/4-

Hub grease cap puller -VW 637/2-

Torque wrench -V.A.G 1332-

Tool insert -T10162 A-

Torque wrench -V.A.G 1410-

Removing

–	Loosen wheel bolts.

–	Raise vehicle.

–	Remove wheel.

–	Detach brake carrier with brake caliper and tie to body with wire → Brake system; Rep. gr.46.

Note

Hang brake caliper from body.

–	Remove bolt for brake disc and remove brake disc.

–	Loosen grease cap from seat by tapping lightly on the claw of the hub grease cap puller -VW 637/2--1-.

Removing and installing wheel bearing unit, torsion beam axle

–	Pry off grease cap.

1 -	Hub grease cap puller -VW 637/2-

Removing and installing wheel bearing unit, torsion beam axle

–	Unscrew bolt -1- using bit XZN 18 -T10162 A--2-.

Caution

Do not use an impact driver when removing bolt -1- with socket -T10162 A--2-!

–	Pull wheel bearing unit off stub axle.

Caution

Avoid soiling and damage to seal when placing on a surface or storing.

Removing and installing wheel bearing unit, torsion beam axle

Wheel bearing -1- must always face upwards.

–	Always set wheel bearing unit on hub -2- when placing on a surface.

Installing

Install in reverse order of removal, observing the following:

–	Carefully push wheel hub/wheel bearing unit onto stub axle.

Caution

Ensure that the wheel hubs/wheel bearing unit does not cant!

–	Screw in new bolt and tighten to specified torque.

Note

First tighten bolt to specified torque setting using torque wrench.

Removing and installing wheel bearing unit, torsion beam axle

Use a rigid spanner for turning further by angle.

Caution

Do not use an impact driver when tightening bolt -1- with socket -T10162 A--2-!

Removing and installing wheel bearing unit, torsion beam axle

–	Drive in dust cap.

1 -	Fitting sleeve -3241/4-

Always renew removed grease caps.

Damaged grease caps may allow moisture to enter the bearing. Therefore, always use the tool shown in the illustration.

Specified torques

→ Chapter „Assembly overview - wheel bearing assembly, torsion beam axle“

→ Chapter „Torque settings for wheel bolts“

Bolts for heat shield, brake caliper and brake disc → Brake system; Rep. gr.46

Removing and installing wheel bearing unit, torsion beam axle

Removing and installing wheel bearing housing, multi-link suspension, four-wheel drive

Special tools and workshop equipment required Torque wrench -V.A.G 1332- ...

Removing and installing wheel bearing unit, multi-link suspension, front-wheel drive

Special tools and workshop equipment required Fitting sleeve -3241/4- Hub grease cap puller -VW 637/2- Torque wrench -V.A.G 1332- ...

Other materials:

Checklist
Carry out the steps in the specified order : To ensure that the engine oil reading is correct, park the vehicle on a level surface with the engine at operating temperature. Switch off the engine and wait a few minutes for the engine oil to flow back into the sump. Open t ...

Checking
Switch off ignition. – Connect manifold gauge (air conditioner service station). – Read pressure gauge. It may display two results, A and B. Ambie ...

Diesel
First read and observe the introductory information and safety warnings Diesel The service intervals are shorter if you use diesel with a high sulphur content ⇒ BookletService schedule, . A Volkswagen dealership will be able to tell you which countries have diesel with a high sulphur c ...