Volkswagen Golf Service & Repair Manual: Removing and installing swivel joint
| Special tools and workshop equipment required |
| Ball joint puller -3287 A- |
| Angle wrench -V.A.G 1756- |
| Ring spanner insert -V.A.G 1332/10- |
| – |
Loosen drive shaft bolt at wheel hub
→ Chapter. |
Caution
| Wheel bearings must not be subjected to load after
bolt securing drive shaft to wheel hub has been
loosened. |
| If wheel bearings are loaded with weight of vehicle,
bearing will be damaged. This reduces the service life
of the wheel bearing. |
| It is not permissible to loosen drive shaft bolt
more than 90° if vehicle is standing on its wheels. |
| Do not attempt to move the vehicle without the drive
shafts fitted as this would damage the wheel bearing. If
a vehicle nevertheless has to be moved, comply with the
following: |
| Install an outer joint instead of the drive shaft. |
| Tighten outer joint to 120 Nm. |
|
|
|
|
| Vehicles with vehicle level sender |
| – |
Pull bracket -2- for front left
vehicle level sender -G78- and/or for front right vehicle level
sender -G289- out of suspension link -3-,
as applicable |
| Continuation for all vehicles |
|
|
|
| – |
Pull drive shaft slightly out of wheel hub. |
| If drive shaft cannot be pulled out of the wheel bearing by
hand, use press tool -T10520-. |
|
|
|
| Before using press tool -T10520- ensure that thrust piece
-1- is inserted. |
| Using press tool -T10520-: |
|
|
|
| – |
To be able to press out drive shaft
-3-, secure press tool -T10520--1-
to wheel hub using 3 wheel bolts -2-. |
|
|
|
| – |
It is essential to follow specified sequence. |
| I - |
Tighten knurled nut -1-
hand-tight. |
| II - |
Turn only bolt -2- using a
spanner in order to press out drive shaft with press tool
-T10520-. |
 Note
| At the end of the procedure or for pressing out drive shaft
further the spindle must be moved to its original position in
order to deploy the hydraulic force! |
| – |
Pull swivel joint out of suspension link. |
| – |
Bend suspension link downwards as far as necessary. |
|
|
|
| – |
Loosen nut from suspension link -2-
but do not remove completely. |
Caution
| Leave nut screwed on a few turns to protect thread
on pin. |
|
| – |
Press swivel joint off wheel bearing housing using ball
joint puller -3287 A--1-. |
| – |
Unscrew nut, and remove swivel joint
-2-. |
| Install in reverse order of removal, observing the
following: |
| – |
Fit swivel joint in wheel bearing housing. |
| – |
Fit drive shaft in wheel hub. |
| – |
Screw on new self-locking nut and counterhold with Torx key
-T40-. |
|
|
|
Checking axial play
–
Firmly pull suspension link down in
-direction of arrow- and press up again.
...
Special tools and workshop equipment required
Assembly tool -T10219-
Thrust plate -VW 402-
Press tool -VW 411-
...
Other materials:
Removing and installing evaporator
Note
The illustration shows a left-hand drive vehicle. The
removal and installation procedure is identical for both
versions.
Removing
–
Observe instructions when working on refrigerant circu ...
Warning and indicator lamps
First read and observe the introductory information
and safety warnings
Lit up
Possible cause
Solution
Electromechanical steering not functioning.
The steering should be checked by a qualified workshop
as soon as possible.
...
Adaptive cruise control
Calibrating adaptive cruise control (ACC), except for e-Golf
Before adjustment of the Adaptive Cruise Control (ACC)
system, the sensor, the retainers and securing elements are to
be checked for damage, external influence and secure sea ...
© 2016-2024 Copyright www.vwgolf.org
Checking swivel joint
Renewing front bonded rubber bush for lower suspension link