Volkswagen Golf Service & Repair Manual: Removing and installing spring, multi-link suspension, right spring for
front-wheel drive
Special tools and workshop equipment
required |
|
|
|
Spring compressor -V.A.G 1752/1- |
|
|
|
Spring retainer -V.A.G 1752/3A- |
Adapter -V.A.G 1752/9-, not illustrated |
– |
Remove rear wheel housing liner
→ General body repairs, exterior; Rep. gr.66. |
|
|
|
– |
Unscrew bolts -1- for shock
absorber -2-. |
|
|
|
– |
Press lugs -arrows- of assembly
aid -1- inwards. |
– |
Remove assembly aid -1-
upwards. |
|
|
|
– |
Fit spring retainer -V.A.G 1752/3A--1-
along with adapter -V.A.G 1752/9--2-
to uppermost spring coil -3-. |
|
|
|
When the spring is renewed, this must be clamped into the
spring compressor -V.A.G 1752/1- as described in following
description: |
– |
Clamp uppermost 4 coils of spring -1-
in spring compressor -V.A.G 1752/1- to stop. The end of the coil
spring must lie against the spring retainer -V.A.G 1752/3A--arrow-. |
WARNING
Ensure that coil spring is seated correctly in
spring retainer -V.A.G 1752/3A- (risk of accident). |
|
– |
Check that the lower spring plate is not damaged. |
– |
If necessary, renew lower spring plate. |
– |
Place lower plate onto bottom of coil spring. |
|
|
|
End of spring -arrow- must lie
against stop on bottom spring seat. |
– |
Mount spring together with spring plate. |
– |
The bottom spring seat has a pin. |
|
|
|
– |
Insert this pin in holes in lower transverse link
-arrow-. |
– |
Insert upper spring seat into upper end of spring. |
|
|
|
– |
Bead of spring seat -arrow-
must lie against coil spring correctly. |
|
|
|
– |
Release tension on spring -4-
while locating upper spring seat on lug on body. |
– |
Unbolt spring compressor-3-
from adapter -V.A.G 1752/9--2- and
remove. |
1 - |
Spring retainer -V.A.G 1752/3A- |
2 - |
Adapter -V.A.G 1752/9- |
3 - |
Spring compressor -V.A.G 1752/1- |
|
|
|
– |
Remove spring retainer -V.A.G 1752/3A--1-
with adapter -V.A.G 1752/9--2-. |
|
|
|
– |
Insert assembly aid -1- and
press downwards. |
– |
Lugs -arrows- must engage. |
→ Chapter „Torque settings for wheel bolts“ |
|
|
|
Special tools and workshop equipment
required
Spring compressor -V.A.G 1752/1-
&nb ...
Other materials:
Sensors
Removing and installing steering angle
sender -G85-
Note
The steering angle sender -G85- is a component of the
steering rack.
It cannot be renewed as an individual part.
...
Removing and installing mirror trim
Special tools and workshop equipment
required
Torque wrench -V.A.G 1783
Note
Removal and installation are described only for the left mirror
trim. The right side is simi ...
Mounting front seat on seat repair stand
Special tools and workshop equipment
required
Torque wrench -V.A.G 1331
Torque wrench -V.A.G 1783
...
© 2016-2024 Copyright www.vwgolf.org