Volkswagen Golf Service & Repair Manual: Removing and installing shock absorber, multi-link suspension, left shock
absorber
Special tools and workshop equipment required |
Torque wrench -V.A.G 1332- |
Torque wrench -V.A.G 1410- |
Spring compressor -V.A.G 1752/1- |
Spring retainer -V.A.G 1752/3A- |
Adapter -V.A.G 1752/9-, not illustrated |
– |
Remove rear wheel housing liner
→ General body repairs, exterior; Rep. gr.66. |
Vehicles with vehicle level sender |
|
|
|
– |
Remove retainer for rear left vehicle level sender-2-. |
Vehicles with adaptive chassis control DCC |
|
|
|
– |
Disconnect connector -1- on
shock absorber -2-. |
– |
Pull line -3- off shock
absorber -2--arrow-. |
Note
If there is moisture in the area of the connector, blow
compressed air on the contacts on the shock absorber and the
connector. |
Continuation for all vehicles |
|
|
|
– |
Insert spring compressor-3-. |
1 - |
Spring retainer -V.A.G 1752/3A- |
2 - |
Adapter -V.A.G 1752/9- |
3 - |
Spring compressor -V.A.G 1752/1- |
WARNING
Ensure that coil spring is correctly seated in
spring retainers -V.A.G 1752/3A--2-. |
|
– |
Compress coil springs until load on shock absorber is
relieved. |
|
|
|
– |
Unscrew bolts -1- for shock
absorber -2-. |
Vehicles with stone guard |
|
|
|
– |
Remove spreader rivet -1-. |
– |
Remove bolts -2- for stone
guard -3-. |
– |
Remove stone guard -3- from
lower transverse link -4-. |
Continuation for all vehicles |
|
|
|
– |
Unscrew nut -1- and remove bolt
-2-. |
Install in reverse order of removal, observing the
following: |
The threaded connections of the shock absorber to the lower
transverse link may only be loosened and tightened in the
unladen weight position
→ Chapter. |
– |
On vehicles with vehicle level sender, carry out basic
settings for wheel damper electronics → Vehicle
diagnostic tester. |
→ Chapter „Assembly overview - suspension strut, shock absorber,
spring, multi-link suspension“ |
→ Chapter „Assembly overview - transverse link“ |
→ Chapter „Torque settings for wheel bolts“ |
Wheel housing liner
→ General body repairs, exterior; Rep. gr.66. |
|
|
|
Special tools and workshop equipment required
Torque wrench -V.A.G 1332-
Torque wrench -V.A.G 1410-
Spring compressor -V.A.G 1752/1 ...
Special tools and workshop equipment required
Torque wrench -V.A.G 1332-
Torque wrench -V.A.G 1410-
Spring compressor -V.A.G 1752/1 ...
Other materials:
Assembly overview - window regulator
1 -
Front door
2 -
Rear window regulator motor -V26/V27-
The door control unit is installed in door separated from window
regulator motor
Removing and installing
→ Chapter
3 -
Hexagon nut
...
Run-flat tyres, structure of a PAX tyre
Run-flat tyres (PAX) are specially developed tyres that
differ from conventional tyres as follows:
PAX tyre with support ring
–
-I- Pax tyre with regular tyre
pressure
...
Removing and installing coolant pipes at heat exchanger (Valeo)
Note
There are different designs and makes of heater and air
conditioning unit. The individual components of the various
heaters and air conditioning units are similar but not identical
(distinguishing features
→ Chapter). The c ...
© 2016-2024 Copyright www.vwgolf.org