Volkswagen Golf Service & Repair Manual: Removing and installing rear axle, multi-link suspension, front-wheel drive,
except for e-Golf and Golf GTE
Special tools and workshop equipment required |
Torque wrench -V.A.G 1332- |
Engine and gearbox jack -V.A.G 1383 A- |
Tensioning strap -T10038- |
Removing subframe with attachments |
|
|
|
– |
Unplug electrical connector -1-
from ABS speed sensor on both sides and move clear. |
– |
Unplug electrical connector -2-
from electromechanical parking brake motor on brake caliper on
both sides. |
– |
Detach electrical wiring harness from retainers
-arrows- and move clear. |
Vehicles with vehicle level sender |
|
|
|
– |
Disconnect connector -1-. |
– |
Take rear left vehicle level sender -G76--3-
off transverse link. |
Continuation for all vehicles |
– |
Remove springs
→ Chapter. |
|
|
|
– |
Unscrew nut -1- and remove bolt
-2-. |
|
|
|
– |
Pull out retaining clip -1- on
both sides of vehicle. |
– |
Free brake lines from holder. |
Note
– |
Remove brake calipers on both sides and tie to body with
brake lines connected
→ Brake system; Rep. gr.46. |
– |
Remove rear silencer of exhaust system
→ Rep. gr.26. |
|
|
|
– |
Use tensioning straps -T10038--1-
to strap vehicle to support beams of lifting platform on both
sides. |
WARNING
If the vehicle is not strapped down, there is a
great danger that the vehicle will slip off the lifting
platform! |
|
– |
Fix position of subframe
→ Chapter. |
|
|
|
– |
Unclip electrical wire -2- on
mounting bracket -1- and move
clear. |
– |
Mark installation position of mounting bracket
-1- on body. |
– |
Carefully lower subframe with attachments a maximum of 30
mm. |
|
|
|
– |
Unclip brake line from clips -arrows-. |
Note
The clips will be destroyed and must be renewed. |
For reasons of clarity, the illustration shows the subframe
from above in removed state. |
– |
Lower subframe with attachments. |
Note
When lowering, ensure sufficient clearance to brake lines
and electrical wiring. |
Installing subframe with attachments |
Install in reverse order of removal, observing the
following: |
→ Chapter „Assembly overview - trailing arm“ |
→ Chapter „Assembly overview - suspension strut, shock absorber,
spring, multi-link suspension“ |
→ Chapter „Assembly overview - rear vehicle level senders,
multi-link suspension, front-wheel drive“ |
→ Chapter „Torque settings for wheel bolts“ |
Bolts for brake caliper and brake disc
→ Brake system; Rep. gr.46 |
Exhaust pipes double clamp
→ Rep. gr.26. |
On vehicles with vehicle level sender, carry out basic
settings for wheel damper electronics → Vehicle
diagnostic tester |
On vehicles with vehicle level sender, carry out basic
adjustment of headlights
→ Electrical system; Rep. gr.94. |
– |
When does wheel alignment have to be checked
→ Chapter? |
|
|
|
Special tools and workshop equipment
required
Torque wrench -V.A.G 1332-
...
Special tools and workshop equipment required
Torque wrench -V.A.G 1332-
Engine and gearbox jack -V.A.G 1383 A-
Tensioning strap -T10038 ...
Other materials:
Side airbags
Fig. 73 On the left-hand side of the vehicle:
deployment zones of side airbags (variant A). On the side of the front seat: location
and deployment range of the side airbag (variant B)
First read and observe the introductory information
and safety warnings The side airbags are located in th ...
Instrument overview
Fig. 12 Instrument cluster in the dash
panel
First read and observe the introductory information
and safety warnings Descriptions of the instruments :
Rev. counter (running engine speed in revolutions x 1,000
per minute).
The start of the red zone on the dial indicates the ma ...
Assembly overview – Brake system pressure accumulator -VX70-, RHD vehicles
1 -
Brake system pressure accumulator -VX70-
Removing and installing
→ Chapter
2 -
Brake line
To hydraulic unit
With thread M12 x 1
14 Nm
3 -&nbs ...
© 2016-2024 Copyright www.vwgolf.org