VW Golf manuals

Volkswagen Golf Service & Repair Manual: Removing and installing rain and light sensor, vehicles without front camera for driver assist systems

Volkswagen Golf Service & Repair Manual / Electrical system / Windscreen wipe/ wash system / Windscreen wiper system / Removing and installing rain and light sensor, vehicles without front camera for driver assist systems

  Note
The rain and light sensor has a silicon layer (coupling pad) which forms the contact surface to the windscreen.
The rain and light sensor has been designed so that it can be used again. A prerequisite for re-use is that the coupling pad is not damaged or dirty (check!).
If a rain and light sensor -G397- is renewed with a rain and light sensor -G397- having a different part number, the new rain and light sensor -G397- has to be coded → Anchor.
The rain and light sensors -G397- cannot be fitted arbitrarily. Determine the correct rain and light sensor -G397- using the Electronic Parts Catalogue (ETKA).
Removing
–  Switch off ignition and all electrical consumers.
–  If ignition key is present, disengage in position 0 (locked).
–  Remove interior mirror → General body repairs, interior; Rep. gr.68
  Note
Wait at least 1 minute after releasing the retaining clip. This is necessary to ensure that the silicone coating is relieved of tension and will not be damaged during removal.
   
–  Release retaining clip on left and right -arrows-.
–  Starting from top, carefully lever rain and light sensor -G397--1- out of retaining frame on windscreen.
 

Removing and installing rain and light sensor, vehicles without front camera for driver assist systems

–  Release and pull off connector -1- and remove rain and light sensor -G397--2-.
  Caution
Store the removed rain and light sensor -G397- so that the coupling pad cannot be damaged or soiled from dust etc. until it is refitted.
Installing
Install in the reverse order of removal, observing the following:
  Caution
Prior to installation, thoroughly clean the surface of the windscreen within the retaining frame for rain and light sensor -G397-. Make sure to completely remove any remains of the coupling pad adhering to the windscreen.
The surface (coupling pad) of the rain and light sensor -G397- must not be soiled on installation. A sensor with a damaged coupling pad must be renewed → Chapter.
  Note
If the surface of the coupling pad on the rain and light sensor -G397- is soiled, it may be possible to clean it by “sticking on” and then “pulling off” one or more adhesive strips.
–  Clean windscreen in the area of the retaining plate thoroughly.
 

Removing and installing rain and light sensor, vehicles without front camera for driver assist systems

–  If necessary, remove protective cap -1- from new rain and light sensor -G397-.
–  Press grip in direction of arrow -A-.
–  Remove protective cap -1- in direction of arrow -B-.
 

Removing and installing rain and light sensor, vehicles without front camera for driver assist systems

–  Reconnect connector.
–  Insert rain and light sensor -G397--1- into retaining frame on windscreen.
–  Push retaining clip on both sides -arrows- so that it can be heard to engage.
  Note
Even when sensor is installed correctly, small air bubbles may first appear between windscreen and coupling pad. After approx. 10 minutes, the contact surface must be free of bubbles.
If the contact surface is not free of bubbles after 10 minutes, the rain and light sensor -G397- must be removed and installed anew.
Air bubbles between the windscreen and the coupling pad will cause the rain and light sensor -G397- to malfunction.
–  Read event memory and delete sporadic faults of the rain sensor → Vehicle diagnostic tester.
  Note
With the rain sensor disconnected, opening the door, for example, can wake up the CAN bus. The sporadic event entries in the onboard supply control unit must be deleted following repair work.
–  If the rain and light sensor -G397- was renewed, perform coding → Anchor.
Coding the rain and light sensor -G397-.
–  Connect vehicle diagnostic tester → Chapter.
–  Code rain and light sensor -G397- → Vehicle diagnostic tester.
 

Removing and installing rain and light sensor, vehicles without front camera for driver assist systems

Removing and installing rain and light sensor, vehicles with front camera for driver assist systems
  Note The rain and light sensor has a silicon layer (coupling pad) which forms the contact surface to the windscreen. The r ...

Repairing rain and light sensor, TRW
The housings for the rain and light sensors -G397- from various manufacturers differ. The sensor housing with lens unit is always supplied as a ...

Other materials:

Introduction
This chapter contains information on the following subjects:  → Types of front passenger front airbag system    → Indicator lamp    → Description and function of the airbags    → Front airbags    → Switching the front passenger front airbag on and of ...

ACC — Adaptive Cruise Control
  Note   On vehicles with ACC, the trim in the right-hand cover of the front bumper must not be painted during a repair paint job or replacement. The ACC system located behind can become operational due to the thickness ...

Assembly overview - suspension, multi-link suspension, four-wheel drive
1 -  Drive shaft 2 -  Bolt Renew after removing 70 Nm +90° 3 -  Wheel bearing housing Removing and installing → Chapter 4 -  ...

© 2016-2024 Copyright www.vwgolf.org