Volkswagen Golf Service & Repair Manual: Removing and installing lower suspension link, vehicle with dual clutch
gearbox 0D9
| Special tools and workshop equipment
required |
|
|
|
| Torque wrench -V.A.G 1332- |
| – |
If fitted, remove noise insulation
→ General body repairs, exterior; Rep. gr.66. |
| – |
Loosen double clamp of exhaust system
→ Rep. gr.26. |
|
|
|
| – |
Detach exhaust system bracket from subframe
-arrows-. |
|
|
|
| – |
Remove bolts -1- for pendulum
support. |
| – |
Release rear area of wheel housing liner and fold it
forwards. |
|
|
|
| Vehicles with vehicle level sender |
| – |
Pull bracket -2- for front left
vehicle level sender -G78- and/or for front right vehicle level
sender -G289- out of suspension link -3-,
as applicable |
| Continuation for all vehicles |
|
|
|
| – |
Pull suspension link out of swivel joint and turn wheel
bearing housing to outside to relieve suspension link. |
|
|
|
| – |
Unscrew bolts -arrows-.
Counterhold at rear bolt on nut at top while doing so. |
| – |
Press gearbox forwards until front bolt can be removed. When
pressing forwards, make sure that exhaust pipe on subframe does
not tilt. |
|
|
|
| – |
Swivel suspension link -1- to
rear and pull out of subframe in
-direction of arrow-. |
| Install in reverse order of removal, observing the
following: |
|
|
|
| – |
Insert rear suspension link -1-
into subframe in -direction of arrow-
and swivel forwards. |
 Note
| The rear bolt must be secured with a new nut. |
|
|
|
| – |
Tighten bolts -arrows-,
counterholding at rear bolt on nut at top. |
Note
| Lever on vehicle level sender must face towards outside of
vehicle. |
| Thread of vehicle level sender must be screwed into outer
hole in suspension link. Retaining lug for vehicle level sender
must engage in inner hole in order to guarantee correct
installation position. |
| – |
On vehicles with vehicle level sender, carry out basic
settings for wheel damper electronics → Vehicle
diagnostic tester. |
| → Chapter „Assembly overview - lower suspension link, swivel
joint“ |
| → Chapter „Assembly overview - front vehicle level senders“ |
| → Chapter „Torque settings for wheel bolts“ |
| Bolts for pendulum support
→ Rep. gr.10. |
| Bolts for noise insulation
→ General body repairs, exterior; Rep. gr.66. |
| Exhaust pipes double clamp
→ Rep. gr.26. |
| Exhaust system to subframe
→ Rep. gr.26. |
|
|
|
Special tools and workshop equipment
required
Torque wrench -V.A.G 1332-
Removin ...
Checking axial play
–
Firmly pull suspension link down in
-direction of arrow- and press up again.
...
Other materials:
Assembly overview - steering column
Note
Always renew self-locking nuts.
Always renew corroded nuts and bolts.
Always renew nuts and bolts that have been tightened further by a
set angle.
1 -
Central pipe of dash panel
2 -&nb ...
Removing and installing C-pillar trim, saloon
Note
Removal and installation are described for the left
vehicle side. Follow same instructions for the right side as
appropriate.
Special tools and workshop equipment
required
...
Cleaning seat belts
First read and observe the introductory information
and safety warnings Large particles of dirt on the automatic belt prevent
it from rolling back properly and thus from working effectively.
The seat belts must never be removed for cleaning purposes.
Remove dirt with a soft brush .
...
© 2016-2024 Copyright www.vwgolf.org
Removing and installing lower suspension link, vehicle with manual gearbox
or dual clutch gearbox 0CW
Checking swivel joint