Volkswagen Golf Service & Repair Manual: Removing and installing headlight main beam bulb -M30-/-M32- (LED)

Volkswagen Golf Service & Repair Manual / Electrical system / Lights, lamps, switches outside / Headlight / Removing and installing headlight main beam bulb -M30-/-M32- (LED)

Special tools and workshop equipment required

Front-end hook -3370-

Removing and installing headlight main beam bulb -M30-/-M32- (LED)

Torque wrench -V.A.G 1783-

Removing and installing headlight main beam bulb -M30-/-M32- (LED)

Torque screwdriver -VAS 6494-

ESD (electrostatic discharge) workplace -VAS 6613-

Note

Removal and installation are described for the left side. Removal and installation on the right side are carried out in the same way.

Caution

Work on LED modules should be performed only at designated ESD workplaces.

Removing and installing headlight main beam bulb -M30-/-M32- (LED)

Removing

–	Remove headlight → Chapter.

–	Using a hammer, carefully release housing cover -3- along predetermined breaking line -4-.

–	Remove housing cover -3- from headlight.

Removing and installing headlight main beam bulb -M30-/-M32- (LED)

–	Release connectors -3- and pull off.

–	Using front-end hook -3370-, pull retaining clip -1- slightly towards rear to release.

–	At the same time, swing retaining clip -1- upwards -arrows-.

–	Remove LED modules for main beam headlight -2- towards rear from headlight.

Removing and installing headlight main beam bulb -M30-/-M32- (LED)

Installing

WARNING

Avoid any skin contact with the heat-conductive paste!

If heat-conductive paste did get onto the skin, clean the affected area thoroughly using soap solution, for example.

–	Apply a thin coat of heat-conductive paste -1- and -2- ( → Electronic Parts Catalogue “ETKA”) at side contact surfaces of LED modules -3-.

Note

Make sure not to interchange the LED modules. Due to their shape, LED modules can only be installed at position given.

Removing and installing headlight main beam bulb -M30-/-M32- (LED)

–	Insert LED modules for main beam headlight -2- into headlight, and fit them in installation position.

–	Swing retaining clips -1- downwards in opposite -direction of arrows-, and engage them audibly.

–	Fit connectors -3-.

Removing and installing headlight main beam bulb -M30-/-M32- (LED)

Caution

Risk of damage to the headlight.

Make sure the housing cover is correctly seated when installing. The ingress of water will lead to permanent damage to the headlight.

–	Fit new housing cover -2- onto headlight.

–	Screw in and tighten bolts -arrows B-.

–	Install headlight → Chapter.

–	Check headlight setting and adjust headlight if necessary → Booklet36.1

Specified torques

→ Chapter „Assembly overview - LED headlights“

Removing and installing headlight main beam bulb -M30-/-M32- (LED)

Removing and installing headlight main beam bulb -M30-/-M32- (dual halogen headlights)

Note Removal and installation are described for the left side. Removal and installation on the right side are carried out in the same way. ...

Removing and installing gas discharge bulb -L13-/-L14-

WARNING Risk of death due to high voltage! Risk of injury and environmental pollution! Ob ...

Other materials:

Crimping pliers -VAS 1978/1A
Crimping pliers -VAS 1978/1A- or crimping pliers (base tool) -VAS 1978/1-2- together with head adapter 0.35 - 2.5 mmІ -VAS 1978/1-1- or head adapter 4.0 - 6.0 mmІ -VAS 1978/2A- are used to squeeze together crimp connectors from ...

Assembly overview - fuel delivery unit/fuel gauge sender, vehicles with front-wheel drive
1 - Fuel delivery unit With fuel system pressurisation pump -G6-. With integrated fuel filter; cannot be renewed individually. With integrated pressure limiting valve; cannot be renewed individually. C ...

Assembly overview - impact bar
1 - Impact bar 2 - Guide bracket Left and right 3 - Hexagon nut Qty. 2 on each side 2.0 Nm 4 - Bolt Qty. 2 on each side 8 Nm 5 - Bolt ...