Volkswagen Golf Service & Repair Manual: Removing and installing drive shaft
Special tools and workshop equipment
required |
|
|
|
Torque wrench -V.A.G 1332- |
|
|
|
– |
Remove retainer for rear left vehicle level sender-2-. |
Vehicles with adaptive chassis control DCC |
|
|
|
– |
Disconnect connector -1- on
shock absorber -2-. |
– |
Pull line -3- off shock
absorber -2--arrow-. |
Note
If there is moisture in the area of the connector, blow
compressed air on the contacts on the shock absorber and the
connector. |
Vehicles with stone guard |
|
|
|
– |
Remove spreader rivet -1-. |
– |
Unscrew bolts -2- for stone
deflector -3-. |
Continuation for all vehicles |
|
|
|
– |
Unscrew nut -1- from coupling
rod -2-. |
– |
Pull coupling rod -2- out of
anti-roll bar -3-. |
|
|
|
– |
Unscrew bolts -arrows- for
anti-roll bar -1-. |
– |
Pull anti-roll bar -1- off
subframe -2- and swing it
downwards. |
|
|
|
– |
Unscrew nut -1- and pull out
bolt -2- securing shock absorber. |
– |
Unscrew nut -3- and pull out
bolt -4- securing wheel bearing
housing. |
|
|
|
– |
Unscrew bolt -1- for track rod
-2- and remove. |
– |
Unbolt drive shaft at gearbox flange. |
– |
Swing wheel bearing housing outwards and pull drive shaft
out of gearbox flange. |
– |
Swing drive shaft downwards and remove from wheel bearing. |
If drive shaft cannot be pulled out of the wheel bearing by
hand, use press tool -T10520-. |
|
|
|
Before using press tool -T10520- ensure that thrust piece
-1- is inserted. |
Using press tool -T10520-: |
|
|
|
– |
To be able to press out drive shaft
-3-, secure press tool -T10520--1-
to wheel hub using 3 wheel bolts -2-. |
|
|
|
– |
It is essential to follow specified sequence. |
I - |
Tighten knurled nut -1-
hand-tight. |
II - |
Turn only bolt -2- using a
spanner in order to press out drive shaft with press tool
-T10520-. |
Note
At the end of the procedure or for pressing out drive shaft
further the spindle must be moved to its original position in
order to deploy the hydraulic force! |
Install in reverse order of removal, observing the
following: |
The threaded connections of the wheel bearing housing may
only be loosened and tightened in the unladen weight position
→ Chapter. |
On vehicles with vehicle level sender, carry out basic
settings for wheel damper electronics → Vehicle
diagnostic tester. |
Before fitting the outer joint in the wheel hub, apply a
thin coat of assembly paste to the splines on the outer joint
→ Electronic Parts Catalogue “ETKA”. |
→ Chapter „Assembly overview - drive shaft“ |
→ Chapter „Assembly overview - transverse link, multi-link
suspension, four-wheel drive“ |
→ Chapter „Assembly overview - track rod, multi-link suspension,
four-wheel drive“ |
→ Chapter „Assembly overview - suspension strut, shock absorber,
spring, multi-link suspension“ |
→ Chapter „Removing and installing rear left vehicle level
sender -G76-, multi-link suspension, front-wheel drive“ |
→ Chapter „Loosening and tightening threaded connections of
drive shaft“ |
→ Chapter „Torque settings for wheel bolts“ |
On vehicles with vehicle level sender, carry out basic
adjustment of headlights
→ Electrical system; Rep. gr.94. |
|
|
|
1 -
Outer constant velocity joint
Renew only as complete unit
Removing
→ Fig..
Installing: drive onto shaft ...
Special tools and workshop equipment required
Thrust plate -VW 401-
Thrust plate -VW 402-
Press tool -VW 408 A-
Press t ...
Other materials:
Brush grinder set -VAS 6776
Designation:
Brush grinder set -VAS 6776-
Product description:
The device is designed to clean surfaces and to remove
corrosion in areas that are difficult to reach. Suitable for
joints, groo ...
Engine cooling
Since higher demands are placed on the engine cooling system
when a trailer is being towed, the cooling system is uprated in
conjunction with factory fitted towing attachments if this is a
technical necessity. This is carried out, for example, by
install ...
Removing and installing seat trim on sill side, standard seat
Note
Removal and installation are described for the left vehicle
side. Follow same instructions for the right side as
appropriate.
Special tools and workshop equipment
required
...
© 2016-2024 Copyright www.vwgolf.org