Volkswagen Golf Service & Repair Manual: Removing and installing catalytic converter
 Note
| The catalytic converter is removed together with the front
exhaust pipe. |
| Special tools and workshop equipment
required |
| High-temperature paste
→ Electronic Parts Catalogue. |
Note
| Reinstall all cable ties in the same locations when
installing. |
|
|
|
| – |
Detach electrical connectors -1-
and -2- from bracket, unplug
connectors and move electrical wiring clear. |
|
|
|
| – |
Unscrew bolt -2- and remove
screw-type clip. |
| – |
Remove bolt -1- and nuts
-arrows-. |
| Vehicles with engine preheater heater element -Z97- |
| – |
Unclip locking mechanism -arrow-. |
|
|
|
| – |
Pull off wiring -1- on engine
preheater heater element -Z97--2-. |
|
|
|
| – |
Unscrew nuts -arrows- and
remove engine preheating element -Z97- with bracket. |
| Continuation for all vehicles |
|
|
|
| – |
Unscrew bolts -arrows- of
bracket. |
|
|
|
| – |
Unscrew right nut -arrow- of
bracket. |
|
|
|
| – |
Unscrew nut -arrow- to the left
of the bracket. |
| – |
Remove tunnel cross-piece
→ General body repairs, exterior; Rep. gr.66. |
|
|
|
| – |
Detach connector from retainer and lay wire leading to
lambda probe to one side. |
|
|
|
| – |
Loosen clamp -arrow- and push
it to rear. |
| Vehicles with four-wheel drive |
|
|
|
| – |
Unbolt flexible coupling of propshaft
-1- from bevel box
→ Final drive, differential; Rep. gr.39. |
|
|
|
| – |
Push propshaft -1- as far as
stop in direction of -arrow-. |
| – |
Remove catalytic converter with front exhaust pipe
-2- downwards. |
| Continuation for all vehicles |
|
|
|
| – |
Fit screwdriver -2- in recess
-arrow- on turbocharger and lever
out seal -1-. |
| Installation is carried out in the reverse order; note the
following: |
Note
| Renew seal and self-locking nuts. |
| Coat studs and bolts of catalytic converter with
high-temperature paste; high-temperature paste
→ Electronic Parts Catalogue. |
| – |
Aligning exhaust system free of tension
→ Chapter. |
| → Fig. „“Installing catalytic converter - tightening torque and
sequence”“ |
| → Chapter „Assembly overview - emission control“ |
| → General body repairs, exterior; Rep. gr.66 |
|
|
|
1 -
Bolt
20 Nm
2 -
Bracket
Renew if damaged
3 -
Nut
Specified t ...
Other materials:
Vehicles with torsion beam axle
Removing
–
If fitted, remove rear left underbody trim
→ General body repairs, exterior; Rep. gr.66.
–
Remove rear tunnel cross-piece
→ General body repairs, exterior; ...
Removing and installing rear window wiper motor -V12-
Special tools and workshop equipment
required
Torque wrench -V.A.G 1331-
Removing
–
Remove wiper arm
→ Chapter.
...
Fitting wheel, fitting instructions for Audi
Vehicles with tyre pressure sensor
If the wheels are changed (e.g. switch from summer to winter
tyres), the wheel electronics transmit data as soon as the speed
of the new wheels exceeds 25 km/h. The new wheel electronics' ID
numbers are ...
© 2016-2024 Copyright www.vwgolf.org
Assembly overview - emission control