Volkswagen Golf Service & Repair Manual: Removing and installing A-pillar trim

Volkswagen Golf Service & Repair Manual / General body repairs, interior / Trim, noise insulation / Interior trims / Removing and installing A-pillar trim

Special tools and workshop equipment required

Removal wedge -3409

Torque wrench -V.A.G 1783

Removing

Upper A-pillar trim

Note

Removal and installation are described for the left vehicle side. Follow same instructions for the right side as appropriate.

–	Release upper A-pillar trim -1- from door seal beading.

–	Carefully release upper A-pillar trim -1- starting at top and continuing up to first catch -arrow A- and -arrow B- using removal wedge -3409-.

Caution

When carrying out the steps below, the curtain airbag may become damaged. For this reason, proceed with extreme caution when bending the barbs.

–	Insert a screwdriver between body and curtain airbag in area of each of the 2 upper retaining clips.

–	Bend barbs of the 2 retaining clips with the screwdriver until the retaining clips can be removed.

Caution

Before installing, always renew the 2 upper retaining clips.

–	Pull upper A-pillar trim -1- upwards out of dash panel -arrow C-.

–	Disconnect connector on treble loudspeaker and remove upper A-pillar trim -1-.

Removing and installing A-pillar trim

Remove trim for triangular window.

Note

Removal and installation are described for the left vehicle side. Follow same instructions for the right side as appropriate.

–	Remove upper A-pillar trim → Anchor.

–	Remove A-pillar gap cover → Chapter.

–	Release trim for triangular window -2- with clip -1- in -direction of arrow A- from body mounting.

–	Pull trim for triangular window -2- with clip -1- upwards out of dash panel -arrow B-.

Removing and installing A-pillar trim

Removing lower A-pillar trim on driver side, LHD vehicles

–	Release sill panel moulding from body in area of overlap to lower trim of A-pillar → Chapter.

–	Remove A-pillar gap cover → Chapter.

Removing and installing A-pillar trim

–	Remove bonnet operating lever -3- → General body repairs, exterior; Rep. gr.55.

–	Remove clip -2-.

–	Release lower A-pillar trim -1- in -direction of arrow B- from body. Release lower A-pillar trim from door seal beading while doing so.

–	Remove lower A-pillar trim -1- in -direction of arrow A- from mounting.

Removing lower A-pillar trim on driver side, RHD vehicles

–	Release sill panel moulding from body in area of overlap to lower trim of A-pillar → Chapter.

–	Remove A-pillar gap cover → Chapter.

Removing and installing A-pillar trim

–	Remove bonnet operating lever -3- → General body repairs, exterior; Rep. gr.55.

–	Remove clip -2-.

–	Unclip lower A-pillar trim -1- in -direction of arrow A- from mountings.

–	At the same time, release lower A-pillar trim -1- in -direction of arrow B- from body. Release lower A-pillar trim from door seal beading while doing so.

–	Push floor covering in area of bolted connections aside and unscrew nuts -arrows-.

–	Lift bracket -1- off studs and pull it out from beneath floor covering.

Removing and installing A-pillar trim

Removing lower A-pillar trim on front passenger side

–	Release sill panel moulding from body in area of overlap to lower trim of A-pillar → Chapter.

–	Remove A-pillar gap cover → Chapter.

Removing and installing A-pillar trim

–	Release lower A-pillar trim -1- in -direction of arrow A- from body. Release lower A-pillar trim from door seal beading while doing so.

–	Remove lower A-pillar trim -1- in -direction of arrow B- from A-pillar.

Installing

Note

Before installing, check all fasteners for damage and renew if necessary.
Remove any retaining clips left in body mountings using removal tool -T40280- and fit them in A-pillar trims for installation.
Following installation, ensure that the A-pillars trim are positioned in door seal beading.

Installation is carried out in reverse order.

Specified torques

→ Chapter „Assembly overview - A-pillar trim“

Removing and installing A-pillar gap cover

Note Removal and installation are described for the left vehicle side. Follow same instructions for the right side as appropriate. ...

Removing and installing B-pillar trim, 4-door models and estate

Special tools and workshop equipment required Wedges -T10383 &n ...

Other materials:

Safety precautions when working on the cooling system
Risk of scalding by hot coolant When the engine is warm, the cooling system is under pressure. Danger of scalding due to steam and hot coolant. – Always wear safety gloves. – Always wear safety goggles. – ...

Removing and installing rear left vehicle level sender -G76-, multi-link suspension, four-wheel drive
Special tools and workshop equipment required Torque wrench -V.A.G 1410- Removing – Disconnect co ...

Removing and installing intake manifold sender -GX9-
Intake manifold sender -GX9- consists of: Intake air temperature sensor 2 -G299- Intake manifold pressure sender -G71- Removing – Remove air filter housing ...