Volkswagen Golf Service & Repair Manual: Priming plastic materials
| Adhesion promoter (transparent) |
| |
Adhesion promoter -ALO 822 000 10- (transparent) |
| This transparent adhesion promoter is a versatile
single-pack adhesion promoter for all plastic parts commonly
found on vehicle exteriors. |
| This adhesion promoter is characterised by its excellent
adhesion, high elasticity and easy application. |
| All plastic parts commonly found on vehicle exteriors. |
| |
PP, EPDM, ABS, PC, PPO, PA, R-TPU, PBTP, PVC. |
|
|
|
| The substrate must be free of release agents. |
| Before cleaning plastic parts, temper them for 60 minutes at
+60 °C to “sweat out” the release agents. |
| – |
Clean with anti-static plastic cleaner -LVM 001 001 A2- or
with the milder slow-drying silicone remover -LVM 020 100 A5-. |
 Note
-
| |
The effort required for the necessary cleaning
depends on the type and quantity of the release agent used.
It is recommended to use an emery pad to help in cleaning. |
-
| |
Let the thinner evaporate completely (e.g. air-dry
overnight at ambient temperature or for 30-40 minutes at
+60 °C). |
|
|
|
| – |
Before priming, clean lightly once more with anti-static
plastic cleaner -LVM 001 001 A2- or slow-drying silicone remover
-LVM 020 100 A5- (with anti-static effect). |
|
|
|
| – |
Do not add any thinner! |
| Method of application: “spray”. |
|
|
|
| – |
Application viscosity 4 mm, +20 °C, DIN 53211 |
Note
| Do not add any thinner! The viscosity as supplied is
identical to the application viscosity. |
| Application viscosity 4 mm, gravity-feed spray gun
“compliant” and “HVLP”: |
|
|
|
| – |
Adjust spray nozzle following manufacturer's instructions to
1.2-1.4 mm for “compliancy”. |
| – |
Adjust spray nozzle following manufacturer's instructions to
1.3-1.5 mm for “HVLP”. |
| – |
Adjust spray pressure following manufacturer's instructions
to 2.0-2.5 bar for “compliancy”. |
| – |
Adjust atomising pressure following manufacturer's
instructions to 0.7 bar for “HVLP”. |
|
|
|
| – |
One full coat is 1-2 µm. |
|
|
|
| Air drying at +20 °C ambient temperature, may be resprayed
after 15 minutes |
|
|
|
| After flash-off period at +20 °C, may be resprayed with
2-pack HS surfacer elasticized with elastic additive -ALZ 011
001-. |
| It can then be overpainted with: |
| |
Waterborne base coat and 2-pack HS clear coat |
|
|
|
| Personal protective equipment: |
| |
Adhere to the safety data sheet. |
| |
Wear personal protective equipment during application. |
|
|
|
| Viscosity as supplied |
11 seconds |
| Flash point: |
Above +23 °C |
| The guaranteed shelf life is 24 months from date of
production. May be used until the date stated on the label at
latest if stored in sealed original containers at +20 °C. |
|
|
|
| The prescribed storage temperature is +20 °C. (Do not store
at temperatures below +5 °C.) |
|
|
|
Designation:
2-pack wash primer -LHV 043 000 A2-
Issued 10.2010
Product description
...
Other materials:
Removing and installing wheel bearing unit, multi-link suspension,
front-wheel drive
Special tools and workshop equipment required
Fitting sleeve -3241/4-
Hub grease cap puller -VW 637/2-
Torque wrench -V.A.G 1332-
Tool insert -T10162 A-
Torque wrench -V.A.G 1410-
...
Trailer stabilisation
First read and observe the introductory information
and safety warnings Trailer stabilisation is a subsidiary function of the
electronic stabilisation programme (ESC). The trailer stabilisation function can
detect if an attached trailer is starting to lurch from side to side.
If a lurching ...
Checking radial clearance of conrods
Special tools and workshop equipment
required
Plastigage
Procedure
–
Remove conrod bearing cap.
–
Clean bearing cap and bearing journal.
...
© 2016-2024 Copyright www.vwgolf.org
2-pack wash primer
Surfacer