Volkswagen Golf Service & Repair Manual: Moving to and back from service position

Volkswagen Golf Service & Repair Manual / General body repairs, exterior / Body front / Look carrier / Moving to and back from service position

Special tools and workshop equipment required

Guide pins -T10093-

Adapter -T10467-

Torque wrench -V.A.G 1331-

Moving to service position

Torque wrench -V.A.G 1332-

Note

The lock carrier is a safety-relevant component. The lock carrier must not be repaired for this reason
In the event of damage, renew lock carrier.
For vehicles with adaptive cruise control unit -J428-, the adaptive cruise control unit -J428- must be adjusted anew, whenever the lock carrier has been removed, installed or replaced.
General information and work instructions for the adaptive cruise control unit -J428- can be found in → Electrical system; Rep. gr.27

Moving to and back from service position

Remove front bumper cover → Chapter
Remove headlights → Electrical system; Rep. gr.94.
Remove cable on mounting bracket of electrically operated lid → Chapter.
Unhook filler neck for washer fluid reservoir on carrier -2- → Electrical system; Rep. gr.92.
Only remove one bolt -3- on left and right side of each longitudinal member.
Screw in special tool guide pins -T10093- to left and right longitudinal members where the bolts were previously located.
Remove remaining bolts -3- on left and right side of longitudinal members
The lock carrier with add-on parts -1- can be pulled forwards about 10 cm on the special tool guide pins -T 10093-. When doing this, be careful with the electrical wires/cables leading to lock carrier and, if necessary, detach connectors.
Install special tool adapter -10467- (2 on each side) on left and right between bumper carrier and longitudinal member.

Moving from service position

–	Remove special tool adapter -T10467- on left and right from between bumper carrier and longitudinal member.

–	Push lock carrier together with add-on parts -1- on the guide pins -T10093- and onto the longitudinal member.

–	Place bolts -3- on left and right.

–	Unscrew guide pins -T10093- on left and right.

–	Align lock carrier together with add-on parts -1- to longitudinal members and between wings → Rep. gr.00.

Note

Always fit lock carrier on the bolting points at the foremost position in the elongated hole. Only then can the lock carrier move in a crash situation.
On vehicles equipped with adaptive cruise control unit -J428-, the adaptive cruise control unit -J428- must be readjusted whenever the lock carrier has been removed, installed or renewed.
General information and work instructions for the adaptive cruise control unit -J428- can be found in → Electrical system; Rep. gr.27

Further installation is carried out in reverse order of removal. When proceeding, observe the following:

Note

Make sure that the charge air cooler pressure hoses are properly refitted
Hoses and lines must not be pinched

–	Adjust headlights → Electrical system; Rep. gr.94.

Specified torques

Lock carrier → Chapter „Assembly overview - lock carrier“

Removing and installing lock carrier – petrol/diesel

Note The lock carrier is a safety-relevant component. For this reason, the lock carrier must only be repaired at the points indicated. In the event of damage, renew lock carrier For vehicle ...

Repairing lock carrier. Left headlight mounting

Note Line -2- indicates the position where the tab might break off. – Remove front bumper cover → Chapter. – ...

Other materials:

Lights and vision – functions
First read and observe the introductory information and safety warnings Parking light When the parking lights (left and right turn signals) are switched on, the headlight on the corresponding side of the vehicle lights up along with the tail light and parts of the tail light cluster. The p ...

Driving out of a parking space with the Park Assist system (only parking spaces parallel to side of road)
First read and observe the introductory information and safety warnings Getting out of a parking space Start the engine. Press the button. An indicator lamp lights up in the button when the function is switched on. Press the turn signal lever for the side of the s ...

Removing and installing bulb for number plate light -X4-/-X5-
Note If an LED number plate light is faulty, the entire number plate light must be renewed. Removing: – Switch off ignition and all electrical consumers. – If i ...