Volkswagen Golf Service & Repair Manual: Incorporation of high-voltage heater (PTC) - Z115- into coolant circuit
 Note
| In vehicles with a high-voltage system, the high-voltage
heater (PTC) -Z115- is used as a supplementary heater. |
| In vehicles with a high-voltage system and an auxiliary
heater installed as optional equipment, the high-voltage heater
(PTC) -Z115- can be used for heating the passenger compartment
instead of the auxiliary heater. For additional information,
refer to
→ Auxiliary heater, supplementary heater; Rep. gr.00. |
| In vehicles with a high-voltage system and without an
auxiliary heater installed as optional equipment, the passenger
compartment can be heated via the “Stationary air conditioning”
function and the - Z115- when the ignition is switched off and
at low ambient temperatures (or cooled via the air conditioning
system at high ambient temperatures). |
| Fill coolant and bleed coolant circuit
→ Rep. gr.19. |
| Incorporation of heat exchanger for air conditioning system
and high-voltage heater (PTC) - Z115- into coolant circuit of
engine
→ Rep. gr.19 (coolant hose schematic diagram). |
|
|
|
Note
| The -arrows- indicate the direction of
coolant flow. |
| 1 - |
Heat exchanger for heater in air conditioning unit |
| Incorporation of heat exchanger into coolant circuit of engine
→ Rep. gr.19 (coolant hose schematic diagram). |
| 2 - |
High-voltage heater (PTC) - Z115- (with high-voltage heater (PTC)
control unit - J848-) |
| Check; vehicle diagnostic tester in “Guided fault finding” mode (of
air conditioning system) and → Current flow
diagrams, Electrical fault finding and Fitting locations |
| Removing and installing
→ Chapter |
| For additional information on vehicles with an “auxiliary heater” as
optional equipment, refer to
→ Auxiliary heater; Rep. gr.00. |
| 3 - |
Coolant valve for gearbox -N488- |
| Removing and installing
→ Rep. gr.19 |
| 4 - |
Coolant supply to gearbox |
| Incorporation of auxiliary heater into coolant circuit of engine
(and gearbox)
→ Rep. gr.19 (coolant hose schematic diagram). |
| 5 - |
Coolant supply from engine |
| Incorporation of auxiliary heater into coolant circuit of engine
→ Rep. gr.19 (coolant hose schematic diagram). |
| 6 - |
Coolant return to the engine |
| Incorporation of auxiliary heater into coolant circuit of engine
→ Rep. gr.19 (coolant hose schematic diagram). |
Note
| Depending on the engine, a valve may be installed in the coolant
return section between the coolant changeover valve 2 -N633- and the
engine. The valve prevents coolant from flowing from the engine to the
-N633- when the engine is running
→ Rep. gr.19 (coolant hose schematic diagram). |
| 7 - |
Coolant changeover valve 2 -N633- |
| Incorporation of auxiliary heater into coolant circuit of engine
→ Rep. gr.19 (coolant hose schematic diagram). |
| Removing and installing
→ Rep. gr.19. |
Note
| The -N633- is activated by the respective engine control unit (e.g.
by engine control unit -J623-), if heat output is required from the air
conditioning system and if the vehicles is in electric drive mode
→ Current flow
diagrams, Electrical fault finding and Fitting locations and
vehicle diagnostic tester in “Guided fault finding” mode. |
| If there are customer complaints about poor heat output of the air
conditioning system when engine is running and/or at standstill
(irrespective of whether -Z115- is activated or not), make sure the
coolant changeover valve 2 is installed with correct orientation and
that it works properly → Current flow
diagrams, Electrical fault finding and Fitting locations and
vehicle diagnostic tester in “Guided fault finding” mode. |
| To ensure that the coolant heated by the -Z115- is conveyed through
the heat exchanger of heater and air conditioning unit, the coolant pump
for high-temperature circuit -V467- and the coolant valve for gearbox
-N488- must be activated as well (by the respective engine control
unit). To ensure that the coolant flows into the correct direction, the
non-return valves installed in the coolant circuit must be installed
correctly and they must work properly. For additional information refer
to
→ Rep. gr.19 (coolant hose schematic diagram); vehicle
diagnostic tester in “Guided fault finding” mode and
→ Current flow
diagrams, Electrical fault finding and Fitting locations. |
| 8 - |
Coolant pump for high-temperature circuit -V467- |
| Incorporation into coolant circuit of engine
→ Rep. gr.19 (coolant hose schematic diagram) |
| Removing and installing
→ Rep. gr.19 |
Note
| The -V467- is activated by the respective engine control unit (e.g.
by engine control unit -J623-), if heat output from the air conditioning
system is required → Current flow
diagrams, Electrical fault finding and Fitting locations and
vehicle diagnostic tester in “Guided fault finding” mode. |
| If there are customer complaints about poor heat output of the air
conditioning system when engine is running and/or at standstill
(irrespective of whether -Z115- is activated or not), make sure the
-V467- is installed with correct orientation and that it works properly
→ Current flow
diagrams, Electrical fault finding and Fitting locations and
vehicle diagnostic tester in “Guided fault finding” mode. |
| To ensure that the coolant heated by the -Z115- is conveyed through
the heat exchanger of heater and air conditioning unit, the coolant
changeover valve 2 -N633- and the coolant valve for gearbox -N488- must
be activated as well (by the respective engine control unit). To ensure
that the coolant flows into the correct direction, the non-return valves
installed in the coolant circuit must be installed correctly and they
must work properly. For additional information refer to
→ Rep. gr.19 (coolant hose schematic diagram); vehicle
diagnostic tester in “Guided fault finding” mode and
→ Current flow
diagrams, Electrical fault finding and Fitting locations. |
| 9 - |
Coolant return from gearbox |
| Incorporation of auxiliary heater into coolant circuit of engine
(and gearbox)
→ Rep. gr.19 (coolant hose schematic diagram). |
Note
Fill coolant and bleed coolant circuit
→ Rep. gr.19.
The illustration below shows only some of the compone ...
Other materials:
Removing and installing bracket for onboard supply control unit -J519-, LHD
vehicles
Removing
–
With ignition switched off, disconnect earth cable from
battery
→ Chapter.
–
Remove dash panel
→ General body repairs, interior; Rep. gr.70.
...
Towing attachment type plate
The trailer load and drawbar load details on the type plate
of the towing attachment are test figures for the device. The
approved details for the relevant vehicle could be below the
trailer load and drawbar load specifications of the trailer.
Figures ca ...
Introduction
This chapter contains information on the following subjects:
→ Indicator lamps
→ Auto Hold function
→ Start/stop system
→ Downhill driving assistant
Additional information and warnings:
Volkswagen information system
Infotainment s ...
© 2016-2024 Copyright www.vwgolf.org
Coolant circuit
Incorporation of heat exchanger for high-voltage battery into coolant circuit of
high-voltage system