Volkswagen Golf Owners Manual: Driving data

Volkswagen Golf Owners Manual / Overview of the vehicle / Instrument cluster / Volkswagen information system / Driving data

First read and observe the introductory information and safety warnings

The multifunction display (MFD) shows a variety of travel and fuel consumption data. MFA is called up from the selection menu .

Switching between displays

Vehicles without a multifunction steering wheel: press the rocker switch on the windscreen wiper lever .

Vehicles with a multifunction steering wheel: press the or button .

Driving data recorder

The MFD is fitted with 3 automatic recorders:

Since start

Since refuel

Long-term

The currently selected memory is shown in the display.

Press the button on the windscreen wiper lever or press the button on the multifunction steering wheel to switch between recorders when the ignition is switched on and the recorder is displayed.

Display	Function
Since start	Display and storage of gathered driving and consumption values from the time the ignition is switched on until it is switched off.
Since start	If the journey is continued within approximately 2 hours of the ignition being switched off, the new values are also taken into account. The memory will automatically be deleted if the journey is interrupted for more than 2 hours.
Since refuel	Display and storage of the collected driving and consumption values. The memory is deleted automatically when the vehicle is refuelled.
Long-term	The memory collects journey data for any number of individual journeys up to a total of 19 hours and 59 minutes or 99 hours and 59 minutes journey time or 1,999.9 km or 9,999.9 km distance travelled. If one of these maximum limits^a) is exceeded, the memory is automatically deleted and reset to 0.

Select the memory that you wish to delete.

Press and hold the button on the windscreen wiper lever, or the button on the multifunction steering wheel, for approximately 2 seconds.

Personal selection of displays

You can set which MFD display should appear in the instrument cluster using the button and the and Multifunction display function buttons in the infotainment system .

Examples of display

Display	Function
Consumption	The current fuel consumption is displayed in litres/100 km while the vehicle is in motion, and in litres/hour while the vehicle is stationary.
Average consumption	The average fuel consumption will be shown after a distance of approximately 300 metres has been travelled. The display will show dashes until this point. The displayed value is updated approximately every second.
Fuel range	Approximate calculation of the distance in km that can still be travelled with the current fuel level under the current driving conditions. One factor used for calculating this figure is the current level of fuel consumption.
Driving time	Driving time in hours (h) and minutes (min) that has elapsed since the ignition was switched on.
Distance driven	The distance travelled in km since the ignition was switched on.
Average speed	The average speed will be shown after a distance of approximately 100 metres has been travelled. The display will show dashes until this point. The displayed values will be updated approximately every 5 seconds.
Digital speed display	Current vehicle speed displayed digitally.
Warning at --- km/h or Warning at --- mph	If the saved speed (within the range of 30 km/h (18 mph) and 250 km/h (155 mph)) is exceeded, an acoustic warning will be sounded, along with a visible warning if required.
Oil temperature	Current temperature of the engine oil displayed digitally.

Saving a speed for the speed warning

Select the Speed warning --- km/h display.

Press the button on the windscreen wiper lever, or the button on the multifunction steering wheel to save the current speed and activate the warning system.

If necessary, use the rocker switch on the windscreen wiper lever, or the or buttons on the multifunction steering wheel, within approximately 5 seconds to set the desired speed. Then press the or button again, or wait a few seconds. The speed is now saved and the warning is activated.

To deactivate, press the or button. The stored speed will be deleted.

^a) Changes depending on the instrument cluster version.

Selection menu

First read and observe the introductory information and safety warnings Menu Function See Driving data Information and settings for the m ...

Assist systems menu

First read and observe the introductory information and safety warnings Menu Function Lane Assist Switches the lane departure warning system on and o ...

Other materials:

Checking adjustment of assembly mountings (engine and gearbox mountings)
Procedure The following specifications must be obtained: There must be a distance of -a- = 10 mm between engine support -2- and engine mounting -1-. ...

Assembly overview - add-on parts of heater and air conditioning unit and of air intake box
Note There are different designs and makes of heater and air conditioning unit. The individual components of the various heaters and air conditioning units are similar but not identical. The combined fitting of different makes of component ...

Raising wheel bearing assembly to unladen position (vehicles with coil springs), front axle
Special tools and workshop equipment required Engine and gearbox jack -V.A.G 1383 A- Tensioning strap -T10038- Support -T10149- Caution All bolts on run ...