Volkswagen Golf Owners Manual: Checklist

Volkswagen Golf Owners Manual / If and when / Practical tips / Changing a wheel / Checklist

To ensure your own safety and the safety of your passengers, observe the following actions in the specified order :

Find a firm and level surface suitable for lifting the vehicle.
Switch off the engine. Select a gear if the vehicle has a manual gearbox, or move the selector lever to position P if it has an automatic gearbox Changing gear Changing gear Automatic gearbox see Automatic gearbox_0 Automatic gearbox see Changing gear_0 Automatic gearbox Manual gearbox see Changing gear_0 Manual gearbox . Switch on the electronic parking brake Braking, stopping and parking Brakes Parking .
Chock the wheel diagonally opposite using the collapsible chocks or other suitable objects.
When towing a trailer, unhitch the trailer from the vehicle and park it properly.
Loosen the wheel bolts on the wheel that is being changed Wheel bolts Anti-theft wheel bolts Wheel bolts Changing a wheel Wheel bolts_2 .
Find the jacking point under the vehicle which is closest to the wheel that is being changed.
Insert the crank ⑦ into the opening on the vehicle jack ⑤ .
Raise the vehicle jack until it just fits under the jacking point of the vehicle.
Ensure that the entire surface of the foot of the vehicle jack is resting securely on the ground and that the foot of the vehicle jack is positioned precisely, i.e. vertically beneath the point of application .
Position the vehicle jack. At the same time, continue to crank the claw up until it is in position around the vertical rib underneath the vehicle .
Crank the vehicle jack further until the wheel is just clear of the ground.

WARNING

Incorrect use of the vehicle jack can cause the vehicle to slip off the jack, which can lead to severe injuries. Please note the following to help reduce the risk of injuries:

Only use vehicle jacks that have been approved by Volkswagen for your vehicle type. Other vehicle jacks could slip out of position – this includes vehicle jacks supplied with other Volkswagen models.

The ground must be firm and level. Soft ground or surfaces at an incline under the vehicle jack may cause the vehicle to slip off the jack. If necessary use a large, strong board or similar support for the vehicle jack.

On a hard, slippery surface (such as tiles) use a rubber mat or similar to prevent the vehicle jack from slipping.

Fit the vehicle jack only at the points described. The vehicle jack claw must grip the vertical rib under the door sill securely .

Never place any part of your body (e.g. an arm or leg) underneath the vehicle if the latter is only supported by the vehicle jack.

If you have to work underneath the vehicle, use suitable stands to provide extra support for the vehicle.

Never lift the vehicle when the engine is running, or if the vehicle is tilted to the side or on a gradient.

Never start the engine when the vehicle is raised on a vehicle jack. Engine vibrations can cause the vehicle to fall off the vehicle jack.

WARNING

Ignoring any of the items on this important safety checklist can lead to accidents and severe injuries.

Always follow the instructions in the checklist and observe the general safety procedures.

Lifting the vehicle with the jack

Fig. 224 Jacking points Fig. 225 Vehicle jack at the rear left-hand side of the vehicle First read and observe the introductory information and safety warningsThe jack may be applied only at t ...

Changing a wheel

Fig. 226 Changing a wheel: removing the wheel bolts with the screwdriver handle First read and observe the introductory information and safety warningsRemoving the wheel Read the checklist. ...

Other materials:

Checking operation of belt buckle
Checking belt buckle – Push latch plate into belt buckle until it engages audibly. Check whether locking mechanism is properly engaged by pulling firmly on belt webbing. If latch plate fails ev ...

Operating ParkPilot
Fig. 148 ParkPilot ultrasound sensors around the vehicle, A: in the front bumper, B: in the rear bumper Fig. 149 In the lower section of the centre console: button for switching the ParkPilot on and off First read and observe the introductory information and safety warnings The ParkPilot ...

Safety precautions when working on subframe
It is not permitted to carry out welding and straightening operations on load-bearing or wheel-guiding suspension components. Always renew corroded nuts and bolts. Bonded rubber bushes can be twisted only to ...