Volkswagen Golf Service & Repair Manual: Checking oil pressure
| Special tools and workshop equipment
required |
|
|
|
| Oil pressure tester -V.A.G 1342- |
| Oil level OK: checking
→ Booklet. |
| Engine oil temperature at least 80 °C (radiator fan must
have run once). |
| – |
Remove oil pressure switch for reduced oil pressure -F378-
→ Chapter. |
| – |
Screw oil pressure tester -V.A.G 1342- into hole for oil
pressure switch. |
| – |
Screw oil pressure switch for reduced oil pressure -F378-
into hole in oil pressure tester -V.A.G 1342- to seal it. |
| Check oil pressure at idling and at 2000 rpm |
| Oil pressure at idling speed: at least 0.6 bar. |
| Minimum oil pressure at 2,000 rpm: 1.5 bar. |
| Check oil pressure at 3,800 rpm |
| – |
Remove electrical connection from oil pressure control valve
-N428-
→ Anchor. |
| – |
Increase engine revs to 3800 rpm and read off oil pressure
on the oil pressure tester -V.A.G 1342-. |
| Minimum oil pressure at 3800 rpm: 2.8 bar. |
| If specification is not attained: |
| – |
Connect electrical connection to oil pressure control valve
-N428-
→ Anchor. |
| – |
Interrogate the engine control unit event memory and delete
all event entries
→ Vehicle diagnostic tester. |
| – |
Check valve for oil pressure control -N428- with
→ vehicle diagnostic tester. |
 Note
| Mechanical damage, e.g. to bearings, could also be the cause
for oil pressure being too low. |
| – |
Renew oil pump
→ Chapter. |
| Check oil pressure switch for reduced oil pressure -F378-
(brown): |
|
|
|
| – |
Connect brown wire of tester to earth (-). |
| – |
Connect voltage tester -V.A.G 1527B- to battery positive (+)
and oil pressure switch for reduced oil pressure -F378- (brown)
using cables from auxiliary test set -V.A.G 1594C-. |
| – |
If LED lights up, renew oil pressure switch for reduced oil
pressure -F378-. |
| If LED does not light up: |
| – |
Start engine: At 0.3…0.6 bar the LED must light up,
otherwise renew oil pressure switch. |
| Check oil pressure switch -F1- (blue): |
| – |
Connect voltage tester -V.A.G 1527B- to battery positive (+)
and oil pressure switch -F1- (blue) using cables from auxiliary
test set -V.A.G 1594C-. |
| – |
If LED lights up, renew oil pressure switch oil pressure
switch -F1-. |
| If LED does not light up: |
| – |
Remove electrical connection from oil pressure control valve
-N428-
→ Anchor. |
| – |
Start engine and increase rpm: At pressure of 2.15…2.95 bar
LED must light up, otherwise renew oil pressure switch. |
| – |
Connect electrical connection to oil pressure control valve
-N428-
→ Anchor. |
| – |
Install oil pressure switch for reduced oil pressure -F378-
→ Chapter. |
| – |
Interrogate the engine control unit event memory and delete
all event entries
→ Vehicle diagnostic tester. |
| → Chapter „Assembly overview - oil filter/oil pressure switch“ |
|
|
|
Removing
Note
Fit all heat insulation sleeves in the original position
when installing.
–
Remove ...
Other materials:
Displays
First read and observe the introductory information
and safety warnings
Display
Solution
ProActive occupant protection not available
Go to a qualified workshop and have the system checked.
ProActive occupant protection: function re ...
Assembly overview - suspension, multi-link suspension, four-wheel drive
1 -
Drive shaft
2 -
Bolt
Renew after removing
70 Nm +90°
3 -
Wheel bearing housing
Removing and installing
→ Chapter
4 -
...
Removing and installing ignition/starter switch
Removing
–
Remove lower steering column trim
→ General body repairs, interior; Rep. gr.68.
–
Disconnect electrical connector -1-.
...
© 2016-2025 Copyright www.vwgolf.org
Removing and installing oil pressure regulating valve -N428-
Engine cooling