Volkswagen Golf Service & Repair Manual: Blender
| Blender was developed to guarantee easy blending-in of
2-pack clear coats and top coats. |
| Easy to use in its pure form |
| Good wetting on all substrates |
| Very fine fade-out to the old finish |
| Keep the surfacer area as small as possible. |
| Overpaint with waterborne base coat until surfacer area is
fully hidden (overlapping coats). |
|
|
|
| Blending system for 2-pack clear coats |
| Mixing ratio with 2-pack clear coat: |
| Mix according to the technical data sheet for the clear coat
→ Chapter. |
|
|
|
| – |
Overpaint waterborne base coat with adjusted clear coat,
overlapping the coats. |
|
|
|
| – |
Apply pure blender -LVE 013 100 A2- to the blending area
within the sanded area. |
|
|
|
| Blending system for 2-pack top coats |
| Mixing ratio with 2-pack top coat: |
| Mix according to the technical data sheet for the 2-pack top
coat
→ Chapter. |
|
|
|
| – |
Recoat until surfacer area is fully hidden, overlapping the
coats. |
|
|
|
| – |
Apply pure blender -LVE 013 100 A2- to the blending area
within the sanded area. |
|
|
|
| Air drying at +20 °C ambient temperature: |
| Allow blending areas to dry overnight before polishing |
|
|
|
| Final flash-off time with force drying is at least
5-10 minutes. |
|
|
|
| Force drying at +60 °C material temperature in 30 minutes. |
| – |
The blending areas may then be polished after cooling for
one hour at +20 °C ambient temperature. |
|
|
|
| Final flash-off time with infrared drying is at least
5-10 minutes. |
|
|
|
| Infrared drying with short-wave radiant heater, 10 minutes. |
| – |
The blending areas may then be polished after cooling for
one hour at +20 °C ambient temperature. |
 Note
| Polish the blending areas with fine polishing paste by hand
or with a polishing machine. |
| Finally treat the surface with high-gloss sealer. |
|
|
|
| Personal protective equipment: |
| Adhere to the safety data sheet. |
| Wear personal protective equipment during application. |
|
|
|
| The guaranteed shelf life is 60 months from date of
production. May be used until the date stated on the label at
latest if stored in sealed original containers at +20 °C. |
|
|
|
Designation:
2-pack HS Performance clear coat -LZK 769 K06 A5-
Issued 08.2012
Product description
...
Other materials:
Removing and installing headlight range control regulator -E102-
Note
The removal and installation procedures are described for
LHD vehicles. Removal and installation for RHD vehicles are
similar.
Removing
–
Remove rotary light switch -EX1-
→&n ...
Removing and installing lock carrier – petrol/diesel
Note
The lock carrier is a safety-relevant component. For this reason, the
lock carrier must only be repaired at the points indicated.
In the event of damage, renew lock carrier
For vehicles with adaptive cruise control unit -J428-, the adaptive
cruise control unit -J428- must be adjus ...
Causes of vibration
Vibration can have a number of different causes. Vibration
can also be caused by tyre wear. Tyre wear caused by driving is
not always evenly spread across the entire running surface of
the tyre. This causes slight imbalances which affect the smooth
runni ...
© 2016-2026 Copyright www.vwgolf.org
2-pack HS Performance clear coat
Hardener