Volkswagen Golf Service & Repair Manual: 2-pack MS matt clear coat

Volkswagen Golf Service & Repair Manual / General information, paint / Genuine products / Clear coats / 2-pack MS matt clear coat

Designation:

2-pack MS matt clear coat -L2K 769 020 A2-

Issued 08.2013

Product description

2-pack MS clear coat is a matt clear coat from the 2-pack acrylic system.

Properties:

High elasticity

Matt finish

Can be mixed with both HS and VHS products

The degree of gloss can be adjusted by mixing with 2-pack HS clear coats.

Particularly suitable for refinishing plastic parts

Note

2-pack MS matt clear coat -L2K 769 020 A2- should be used only for small areas (add-on parts of passenger cars).

Technical data sheet

Substrate

Suitable base coats:

Waterborne base coats

Application

Mixing ratio:

–	3:1 by volume with:

2-pack HS hardener -LHA 009 041 A3-

2-pack HS hardener, slow-drying -LHA 009 047 A3-

2-pack HS hardener, extra slow-drying -LHA 009 048 A3-

2-pack MS matt clear coat

Mixing ratio:

–	5:1 by volume with:

2-pack VHS hardener -LHA 009 051 A2-/-LVM 009 051 A5-

2-pack VHS hardener, slow-drying -LHA 009 052 A2-/-LHA 009 052 A3-

2-pack VHS hardener, extra slow-drying -LHA 009 053 A2-

Note

Different HS and VHS hardeners and thinners result in different degrees of gloss.

2-pack MS matt clear coat

The clear coat must be stirred carefully before it is poured out of the tin.

Thinner:

2-pack thinner -LVE 009 001 A5-

2-pack thinner, slow-drying -LVM 009 300 A2-

2-pack thinner, special -LVM 009 200 A2-/-LVM 009 200 A5-

2-pack MS matt clear coat

Application time/pot life:

–	Ready-to-spray preparation approx. 4 hours at +20 °C

2-pack MS matt clear coat

Method of application: “spray”.

2-pack MS matt clear coat

–	The application viscosity at +20 °C is the “compliant” and “HVLP” mixing viscosity.

Application viscosity 4 mm, gravity-feed spray gun “compliant” and “HVLP”:

DIN 4 mm: 14-16 seconds

ISO 4 mm: 28-33 seconds

2-pack MS matt clear coat

Addition of thinner at +20 °C material temperature: 25% HS hardener (3:1) and 30% VHS hardener (5:1)

–	If thinner is added, use measuring stick to mix.

2-pack MS matt clear coat

–	Adjust spray nozzle following manufacturer's instructions to 1.3-1.4 mm for “compliancy” and “HVLP”.

–	Adjust spray pressure following manufacturer's instructions to 2.0-2.5 bar for “compliancy”.

–	Adjust atomising pressure following manufacturer's instructions to 0.7 bar for “HVLP”.

–	Apply in two coats.

2-pack MS matt clear coat

–	Apply one full coat, flash-off 15-20 minutes and then finish painting.

–	The specified thickness for the dry film is 50-60 µm.

Note

Different methods of application result in different degrees of gloss.

2-pack MS matt clear coat

Drying

Air drying at +20 °C ambient temperature:

Dust dry in 2-2.5 hours

Dry for assembly in 5-6 hours

Dry overnight

2-pack MS matt clear coat

Final flash-off time with force drying is at least 15-20 minutes.

2-pack MS matt clear coat

Force drying at +60 °C material temperature in 40-45 minutes.

2-pack MS matt clear coat

Personal protective equipment:

Adhere to the safety data sheet.

Wear personal protective equipment during application.

Data

2-pack MS matt clear coat

Flash point:	Above +23 °C
VOC content: 2004/42/IIB(e)(840)580	The EU limit value for this product (product category IIB.b) in ready-to-spray form is max. 840 g/l of volatile organic compounds. The VOC content of this product in ready-to-spray form is max. 580 g/l.

Storage

Guaranteed storage time of 2-pack MS matt clear coat -L2K 769 020 A2- is 24 months from production date. May be used until the date stated on the label at latest if stored in sealed original containers at +20 °C.

2-pack MS matt clear coat

2-pack HS clear coat

Designation: 2-pack HS clear coat -L2K 769 500 A5- Issued 10.2012 Product description ...

2-pack HS Vario clear coat

Designation: 2-pack HS Vario clear coat -L2K 769 K01 A5- Issued 06.2013 Product description ...

Other materials:

Assembly overview - clutch engagement
1 - Shim for “K 1” Determining thickness → Chapter. 2 - Large engaging lever for “K 1” With engagement bearing Removing and installing → Chapter ...

Removing and installing retaining plate for manually operated anti-dazzle interior mirror, with rain and light sensor -G397- and without front camera for driver assist systems -R242-
Note With the repair procedure described, it is no longer necessary to renew the windscreen. At the same time, it is also possible to reuse the old mirror base which has fa ...

Installing repair kit for headlight housing, does not apply for LED headlights
Special tools and workshop equipment required Torque wrench -V.A.G 1783- Torque screwdriver -VAS 6494- N ...