Volkswagen Golf Service & Repair Manual: 2-pack IR Premium filler
| |
2-pack IR Premium filler -LSP 787 220 A1- |
| |
2-pack IR Premium filler -LSP 787 220 A2- |
| |
2-pack IR Premium filler -LSP 787 220 A3- |
| 2-pack IR Premium filler -LSP 787 220 A1/A2/A3- is a
high-grade polyester filler for passenger car refinishing. |
| |
All common metal substrates |
| |
Very good adhesion to galvanised substrates |
| |
Easy to apply and non-porous |
| |
Especially suitable for IR drying |
| |
Well-sanded factory paint or old paint |
| |
Fully cured, primed two-pack surfacers and two-pack primers |
| |
Cleaned and sanded UP-GF (fibreglass) surfaces, free of
release agents |
Caution
| This filler may not be applied to PVB (acid-curing)
surfaces or 1-pack primer (e.g. synthetic resin). |
| It is also unsuitable for thermoplastic or
viscoelastic paint. |
|
|
|
|
| – |
Carefully remove any grease and sand surface. |
| – |
Isolate any bare metal surfaces using 2-pack wash primer
-LHV 043 000 A2-, and then apply 2-pack HS Performance surfacer.
Sand surfacer after drying. |
| – |
For UP-GF (fibreglass) substrate parts, remove residual
release agents and lightly sand surface. |
| – |
Before recoating all substrates, use a suitable cleaning
agent to ensure a clean surface free of residues. |
|
|
|
| – |
Add 2-3% by weight 2-pack hardener -LVM 018 000 A1/A2- or,
especially at high temperatures, 2-pack hardener, slow-drying
-LVM 018 100 A2-. |
 Note
| Avoid adding too much hardener, as this can lead to bleeding
through, especially with dayglow paints and light metallic
colours. |
| – |
At +20°C ambient temperature, approximately 2-4 minutes |
|
|
|
| – |
At +20°C ambient temperature, approximately 20-30 minutes |
|
|
|
| |
Short-wave radiant heater, 3 minutes (at 50% power) |
| |
Medium-wave radiant heater, 5 minutes |
|
|
|
| After the drying times given above: |
| – |
First sanding dry with P80 to P240-grade sandpaper |
| – |
Second sanding dry with P240 to P400-grade sandpaper |
Note
| Heat resistant to +80 °C. |
|
|
|
| |
Coat fine filler with 2-pack fine filler -LSP 784 002 A2- or
with 2-pack spray filler -ALN 788 007- (except on galvanised
sheet metal). |
| |
Prime sanded-down metal surfaces and filled surfaces again
using 2-pack wash primer -LHV 043 000 A2-, and then apply 2-pack
HS Performance surfacer. |
| – |
Then recoat with top coat. |
Note
| Before applying filler, the entire surface must be dry
sanded with P280 to P400-grade sandpaper. |
|
|
|
| Personal protective equipment: |
| |
Adhere to the safety data sheet. |
| |
Wear personal protective equipment during application. |
|
|
|
| Viscosity as supplied |
pastos |
| Flash point: |
Filler, above 23 °C |
| VOC content:
2004/42/IIB(b)(250)150 |
The EU limit value for this
product (product category IIB.b) in ready-to-spray form is max. 250 g/l
of volatile organic compounds. The VOC content of this product in
ready-to-spray form is max. 150 g/l. |
| The guaranteed shelf life is 12 months from date of
production. May be used until the date stated on the label at
latest if stored in sealed original containers at +20 °C. |
|
|
|
| – |
Storage temperature +20 °C (+30 °C must not be exceeded). |
|
|
|
Designation:
2-pack spray filler -ALN 788 007-
Issued 06/2011
Product description
...
Designation:
2-pack diamond aluminium filler, powder -DA 004 200 A2-
2-pack diamond aluminium filler, hard ...
© 2016-2024 Copyright www.vwgolf.org
2-pack spray filler
2-pack diamond aluminium filler