Volkswagen Golf Service & Repair Manual: 2-pack HS Optimum Plus clear coat
| 2-pack HS Optimum Plus clear coat -LZK 769 K07 A5- |
| 2-pack HS Optimum Plus clear coat is a VOC compliant
high-solid clear coat. Perfectly suitable for application even
under unfavourable operating conditions (such as too low drying
temperature) in the spray booth. |
| Flexible and efficient application. |
| HS spot thinner -LVM 006 000 A2- may be used. |
|
|
|
| 2-pack VHS hardener -LHA 009 051 A2-/-LVM 009 051 A5- |
| 2-pack VHS hardener, fast-drying -LHA 009 050 A2- |
| 2-pack VHS hardener, slow-drying -LHA 009 052 A2-/-LHA 009
052 A3- |
| 2-pack VHS hardener, extra slow-drying -LHA 009 053 A2- |
| See technical data sheet for 2-pack VHS hardener
→ Chapter |
| 2-pack thinner, special -LVM 009 200 A2-/-LVM 009 200 A5- |
| 2-pack thinner, slow-drying -LVM 009 300 A2- |
| HS spot thinner -LVM 006 000 A2- |
| See technical data sheet for HS spot thinner LVM 006 000 A2
→ Chapter. |
| For elasticization, see
→ Anchor |
|
|
|
| Application time/pot life: |
| – |
Mixed for spraying: 45-60 minutes at +20°C (depending on the
hardener used) |
|
|
|
| Method of application: “spray”. |
|
|
|
| – |
The application viscosity at +20 °C is the “compliant” and
“HVLP” mixing viscosity. |
|
|
|
| – |
Adjust spray nozzle following manufacturer's instructions to
1.2-1.3 mm for “compliancy”. |
| – |
Adjust spray nozzle following manufacturer's instructions to
1.3-1.4 mm for “HVLP”. |
| – |
Adjust spray pressure following manufacturer's instructions
to 2.0-2.5 bar for “compliancy”. |
| – |
Adjust atomising pressure following manufacturer's
instructions to 0.7 bar for “HVLP”. |
|
|
|
| – |
Apply in one-and-a-half coats. |
 Note
| The first half-coat should form a nearly complete, thin film
over which a full spray coat is directly sprayed. |
| – |
The specified thickness for the dry film is 40-60 µm. |
Note
| If used as a clear coat to repair minor damage (Clever
Repair spot repair method), the 10 % special 2-pack thinner -LVM
0009 200 A2- and special 2-pack thinner -LVM 009 200 A5- may be
replaced with 10 % HS spot repair thinner -LVM 006 000 A2 HS-.
Do not apply to horizontal surfaces. |
|
|
|
| Air drying at +20 °C ambient temperature: |
| Dust dry in 15-30 minutes |
| Dry for assembly in 2-5 hours |
|
|
|
| Final flash-off time with force drying is 5 minutes. |
|
|
|
| Force drying at +60 °C material temperature with: |
| 2-pack VHS hardener -LHA 009 051 A2-/-LVM 009 051 A5-
15-25 minutes. |
| 2-pack VHS hardener, fast-drying -LHA 009 050 A2-
10-15 minutes. |
| 2-pack VHS hardener, slow-drying -LHA 009 052 A2-/-LHA 009
052 A3- 20-30 minutes. |
| 2-pack VHS hardener, extra slow-drying -LHA 009 053 A2-
25-35 minutes. |
|
|
|
| The final flash-off time with infrared drying is 5 minutes. |
|
|
|
| Infrared drying with short-wave radiant heater, 8-12 minutes |
|
|
|
| Elasticization of rigid and semi-rigid plastics: |
| First mix the base material with 15% elastic additive -ALZ
011 001-. |
| Mixing ratio with 2-pack VHS hardeners: 3:1, with 10 %
2-pack thinner, special -LVM 009 200 A2- or 2-pack thinner,
special -LVM 009 200 A5- (drying time increases). |
|
|
|
| Personal protective equipment: |
| Adhere to the safety data sheet. |
| Wear personal protective equipment during application. |
|
|
|
| Flash point: |
Above +23 °C |
| VOC content:
2004/42/IIB(d)(420)420 |
The EU limit value for this
product (product category IIB.b) in ready-to-spray form is max. 420 g/l
of volatile organic compounds. The VOC content of this product in
ready-to-spray form is max. 420 g/l. |
| The guaranteed shelf life of the 2-pack HS Optimum Plus
clear coat -LZK 769 K07 A5- is 48 months as of production date.
May be used until the date stated on the label at latest if
stored in sealed original containers at +20 °C. |
|
|
|
Designation:
2-pack HS Optimum clear coat -LZK 769 K02 A5-
Issued 10.2012
Product description
...
Designation:
2-pack HS Brillant clear coat -L2K 769 K04 A5-
Issued 10.2010
Product description
...
Other materials:
Safety precautions when working on ignition system
Risk of injury due to electric shock
The ignition system is under high-voltage when the engine is
running. Touching the ignition system may result in an electric shock.
–
Do not touch or disconnect ignition cables when the engine is
running or bei ...
Fitting control unit to hydraulic unit
Special tools and workshop equipment
required
ESD workplace -VAS 6613-
Torque screwdriver -V.A.G 1624-
Torx bit T25
Note
...
Detecting leaks
External damage can cause leaks in the refrigerant circuit. Because a small
leak will involve only small quantities of refrigerant, leaks should be checked
for using an electronic leak detector or by introducing a leak detection
additive to the refrigerant circuit. Electronic leak detectors ca ...
© 2016-2024 Copyright www.vwgolf.org
2-pack HS Optimum clear coat
2-pack HS Brillant clear coat