Volkswagen Golf Service & Repair Manual: 1-pack fill clean spray can -LLS MAX 099-, -LLS MAX 100-, Aquaplus system
| 1-pack FillClean spray can -LLS MAX 099-, 250 ml for
waterborne mixing paint “Aquaplus system” |
| 1-pack FillClean spray can -LLS MAX 100-, 400 ml for
waterborne mixing paint “Aquaplus system” |
| The product is an aerosol can, pre-filled with solvents and
propellant, and especially designed for use with the “Aquaplus
System” and the “Aqua Premium system”. |
| For filling the aerosol can, only the special FillClean
equipment may be used. |
| Field of application: Clever Repair only. |
| The product is an aerosol can, pre-filled with solvents and
propellant, and especially designed for use with the “Aquaplus
System” and the “Aqua Premium system”. |
| The aerosol can does not contain any paint when delivered.
It is a semi-finished product. |
| The ready-to-use end product is produced through filling the
pre-filled aerosol can with 100 ml of undiluted Aquaplus or Aqua
Premium basecoat using the special FillClean equipment. |
| The ready-to-use (filled with paint) aerosol must always be
labelled accordingly, prior to further use. For this purpose, a
special label indicating the respective colour, generated and
printed by the tinting system, can be used. |
| It is essential to ensure that all the data given in the
example below is present on this label. |
| The content of 316 ml (0.32 l) declarated on the label
refers to the final product (after filling with paint). |
| The aerosol can, pre-filled with 216 ml propellant and
solvents, is filled with additional 100 ml Aquaplus or Aqua
Premium basecoat, incl. additive for Aqua Premium -LVM 035 200-
or additive for Aqua Premium -LVM 035 301-. |
 Note
| Protective garments and equipment in accordance with work
safety regulations must be worn. |
| Set up the FillClean equipment in a well ventilated room. |
| The maximum capacity of the aerosol can must not be exceeded
when filling. Risk of explosion! |
| No poisonous carcinogenic substances or halocarbons must be
used for filling the aerosol cans. |
| Warning: electrostatic discharge! Only use a damp cloth for
cleaning of plastic parts. |
| Any repairs must be performed by a qualified technician. |
| Paint residues must be removed from the machine at regular
intervals. Use a cloth and an appropriate solvent for this
purpose. |
| The pressure supply line must be checked at regular
intervals. |
| FillClean filling process |
| Observe the operating instructions of the filling equipment. |
|
|
|
| – |
Put filling pad on indenter. |
|
|
|
| – |
Fit FillClean filling cylinder onto spray can. |
|
|
|
| – |
Fit and push down the FillClean cap. |
|
|
|
| – |
Fill the aerosol can with paint. |
|
|
|
| – |
Set FillClean can and filled cylinder into upper groove
-1- of the FillClean machine. |
Note
| When the FillClean can is inserted into the upper groove
-1-, the lower rotating plate
-2- must first be positioned at the
very bottom. As soon as the FillClean can has been inserted into
the upper groove -1-, turn the
rotating plate -2- upwards to use
it as a counterhold. |
|
|
|
| – |
Push the button to the right to trigger filling. Wait
approx. 10 seconds. |
|
|
|
| – |
After filling, remove filling cylinder
-2- from FillClean can. |
| – |
Remove FillClean cap -1- from
filling cylinder -2-. |
| – |
Fit spray nozzle -3- onto
FillClean can. |
|
|
|
| – |
Leave the pad in the cap to indicate the filled colour tone. |
| – |
The FillClean can is now ready to use. |
| 1-pack wash primer -LVM 044 007 A2-/-LVM 044 171 A2- |
| 2-pack plastic adhesion surfacer -LKF 696 009 A2-/-LKF 696
040 A2- |
| For plastic surfaces, refer to
→ Remark. |
|
|
|
| – |
Thoroughly clean factory or old paintwork and/or 2-pack HS
surfacer using silicone remover -LSW 019 000 A5-. If severely
soiled, pre-clean with slow-drying silicone remover -LVM 020 100
A5-. |
|
|
|
| – |
Dry sand using orbital sander (P400 to P500 grade) and dust
collector. |
|
|
|
| – |
Wet-sand with P800 to P1000-grain sandpaper. |
|
|
|
| – |
Before recoating the sanded substrates, thoroughly clean
them of dust, sanding residue and other dirt using silicone
remover -LSW 019 000 A5-. |
| Wipe off any excess silicone remover with a lint-free cloth,
leaving no streaks. Observe technical data sheet
→ Chapter „Silicone remover“. |
| Areas sanded to bare metal must be primed with 1-pack wash
primer -LVM 044 007 A2-/-LVM 044 171 A2-. |
| Bare metal spots must not be larger than 5.0 cm in diameter. |
| If 2-pack HS surfacer is used, bare metal spots must be
primed using 2-pack wash primer -LHV 043 000 A2- or 1-pack wash
primer -LVM 044 007 A2-/-LVM 044 171 A2-. |
| It is recommended to test the colour tone on a spray sample
prior to application. |
|
|
|
| – |
Shake aerosol well (at least 2 minutes) to ensure proper
mixing. |
|
|
|
| Method of application: “spray”. |
| – |
Maintain a distance of 20-25 cm. |
| – |
The specified thickness for the dry film is 15-20 µm. |
|
|
|
| – |
Apply in 2 spray passes (1 normal coat followed by 1 finish
coat) with 5-10 minutes intermediate flash-off time. |
Note
| With low opacity colours, it may be necessary to apply an
additional spray cote (wet-on-wet). |
| As an alternative, wait until the paint film appears matt
prior to the application of the additional spray coat. |
| To prevent clogging of the nozzle, after each use (or any
interruption of the spray operation), hold the can upside down
and press the spray button until the material flow stops (i.e.
until the valve is empty). |
|
|
|
| Flash-off time is 15 to 30 minutes at an ambient temperature
of +20 °C. Important note: Observe flash-off time (coated
surface must appear matt). |
| 2-pack HS clear coat (see relevant data sheet). |
| 2-pack clear coat -LLS MAX 210- (also recoatable with other
2-pack HS clear coats). |
Caution
| Protective garments and equipment in accordance with
work safety regulations must be worn. |
| Observe safety information sheets as well as
warnings on the label of the spray can. |
| After filling the can, shake it for approx
2 minutes. |
| Before applying, shake can for approx 2 minutes. |
| Shake again briefly before spraying each coat. |
| After fully emptying the spray can, dispose of as
recycling material |
|
|
|
|
| VOC content:
2004/42/IIB(e)(840)690 |
The EU limit value for this
product (product category IIB.b) in ready-to-spray form is max. 840 g/l
of volatile organic compounds. The VOC content of this product in
ready-to-spray form is max. 690 g/l. |
| The guaranteed shelf life of pre-filled aerosol (without
paint) is 24 months. |
| After filling with paint, the shelf life of the aerosol is 4
weeks. |
|
|
|
Designation:
1-pack wash primer -LLS MAX 106 M2-, light grey
1-pack wash primer -LLS MAX 107 M2-, dark grey
...
1-pack fill clean spray can -LLS MAX 112-, 400 ml for
water-based mixing paint “Aquaplus premium system”
Issue 05.2014
...
Other materials:
Stowage compartment on the front passenger side
Fig. 113 Stowage compartment on the front
passenger side
Fig. 114 Open stowage compartment on the
front passenger side
First read and observe the introductory information
and safety warnings Opening and closing the stowage compartment
If necessary, unlock the stowage compartment. The st ...
Warning lamp
First read and observe the introductory information
and safety warnings
Display
Possible cause
Solution
Any or all vehicle doors are open or not closed properly.
Do not drive
on!
Open the appropriate vehicle door and th ...
Removing and installing front tunnel cross-piece
Special tools and workshop equipment
required
Torque wrench -V.A.G 1331-
Removing
–
If fitted, remove centre underbody panel
→ ...
© 2016-2024 Copyright www.vwgolf.org
1-pack wash primer
1-pack fill clean spray can -LLS MAX 112-, Aqua Premium system