Volkswagen Golf Service & Repair Manual: 1-pack anti-corrosion wash primer
| |
1-pack anti-corrosion wash primer -ALN 002 003 10- |
| 1-pack anti-corrosion primer is a zinc chromate-free
one-pack product based on polyvinyl butyral for passenger car
refinishing. |
| The special combination of pigments and binders provides
good corrosion protection and adhesion and is also certified
suitable for application on welded joints. However, because this
product is non-conductive, it is not suitable for use with
spot-weld work. |
| It is recommended to apply a coat of 2-pack HS surfacer over
the 1-pack anti-corrosion wash primer -ALN 002 003 10- at
remaining rust spots on corners and edges, as well as areas
which have been sanded bare. |
| |
Cleaned and sanded electroplated or roller-galvanised steel
panels or soft aluminium |
| |
Lightly sanded factory primer |
| |
Fully cured, solvent-resistant, well-preserved and sanded
factory paint or old paint (with the exception of thermoplastic
paint) |
| |
Surfaces prepared with 2-pack polyester products and then
finely sanded |
|
|
|
| – |
Thoroughly clean with silicone remover -LVM 020 000 A5- or
slow-drying silicone remover -LVM 020 100 A5-. |
|
|
|
| – |
Dry sand using orbital sander with P400 to P500-grain
sandpaper and dust collector. |
|
|
|
| – |
Wet sand with P800 to P1000-grain sandpaper. Completely
remove any rust spots and sand feather edges to old paint. |
|
|
|
| |
2-pack thinner -LVE 009 001 A5- |
| |
2-pack thinner plus -LHA 014 000 A5- |
| |
2-pack thinner, special -LVM 009 200 A2/A5- |
| Method of application: “spray”. |
|
|
|
| – |
Application viscosity 4 mm, +20 °C, DIN 53211 |
|
|
|
| Add 40% thinner at a material temperature of +20 °C |
| – |
If thinner is added, use measuring stick to mix. |
|
|
|
| Application viscosity 4 mm, gravity-feed spray gun
“compliant” and “HVLP”: |
| – |
Adjust spray nozzle following manufacturer's instructions to
1.3-1.4 mm for “compliancy” and “HVLP”. |
| – |
Adjust spray pressure following manufacturer's instructions
to 1.5-3.0 bar for “compliancy”. |
|
|
|
| – |
The specified thickness for the dry film is 15-20 µm. |
| Method of application: “brush” |
 Note
| |
When “brushing”, apply the material in one or two
operations. |
| |
Viscosity as supplied is identical to application
viscosity. |
|
|
|
| Flash-off time is 15-25 minutes at +20 °C ambient
temperature. |
|
|
|
| |
Apply 2-pack HS surfacer
→ Chapter |
 C aution
| Do not recoat with polyester products. |
| Do not recoat with epoxy products. |
| Do not overpaint directly with waterborne base coat. |
| Do not use on thermoplastic paint. |
| The following three-stage structure is recommended: |
| |
Prime with 1-pack anti-corrosion wash primer -ALN
002 003 10- |
| |
Isolate with 2-pack HS surfacer |
| The three-stage structure must be used for
galvanised substrates. |
|
|
|
|
| Personal protective equipment: |
| |
Adhere to the safety data sheet. |
| |
Wear personal protective equipment during application. |
|
|
|
| Viscosity as supplied |
90-100 seconds |
| Flash point: |
Above +23 °C |
| VOC content:
2004/42/IIB(c)(780)780 |
The EU limit value for this
product (product category IIB.c) in ready-to-spray form is max.
780 g/litre of volatile organic compounds. The VOC content of this
product in ready-to-spray form is max. 780 g/l. |
| The guaranteed shelf life is 24 months from date of
production. May be used until the date stated on the label at
latest if stored in sealed original containers at +20 °C. |
|
|
|
Designation:
1-pack wash primer -LVM 044 007 A2-, light grey
1-pack wash primer -LVM 044 171 A2-, dark grey ...
© 2016-2024 Copyright www.vwgolf.org
Priming metal
1-pack wash primer