Volkswagen Golf Owners Manual: Cleaning and caring for natural leather covers
First read and observe the introductory information
and safety warnings
Please contact a Volkswagen dealership or other qualified workshop if you have any questions on cleaning and caring for the leather equipment in your vehicle.
Care and use
Natural leather is sensitive and requires regular care:
- Use a leather cream with sunlight protection and impregnation properties on a regular basis and always after cleaning. The cream nourishes the leather, keeps it breathable and supple and replaces lost moisture. It also protects the surface.
- Leather should be cleaned every 2 to 3 months and fresh stains removed.
- Treat the leather with a special leather care product every six months .
- Always apply cleaning and care products extremely sparingly and always use a dry cotton or woollen cloth that is free from fluff. Do not apply cleaning and care products directly to the leather.
- Remove fresh stains such as ink, ball-point pen ink, lipstick, shoe cream etc. as quickly as possible.
- Look after the pigment. Use a special coloured leather cream to refresh the colour where necessary.
- Wipe it off with a soft cloth.
Cleaning
Volkswagen recommends that you use a damp cotton or wool cloth for general cleaning purposes.
Do not let the water soak through the leather or soak into the seams.
Please observe the following notes prior to cleaning the leather upholstery .
| Type of stain | Cleaning |
|---|---|
| Stubborn stains | – Use a wrung-out cloth to apply a mild soap solution.a). – Dry with an absorbent, dry cloth. |
| Water-based stains, e.g. coffee, tea, juice, blood etc. | – Remove fresh stains with an absorbent cloth, – If the stain has already dried, use a suitable cleaning agent . |
| Oily stains, e.g. oil, lipstick etc. | – Remove fresh stains with an absorbent cloth. – If the stain has not yet penetrated the surface, use a suitable cleaning agent . |
| Difficult stains, e.g. biro, felt tip pen, nail varnish, emulsion paint, shoe polish etc. | – Dry with an absorbent, dry cloth. – Clean with a suitable leather stain remover. |
NOTICE
- Do not use solvents, wax polish, shoe cream, spot removers or similar products on leather.
- Stains cannot be removed if they has been left on the leather for a long time and have penetrated the surface.
- Spilt liquids should be cleaned immediately using an absorbent cloth as the leather surface and the stitching absorb liquids quickly.
- If the car is left standing outdoors for long periods, the leather should be protected against direct sunlight to prevent it from fading.
However, slight colour variations will arise in normal use.
a) Mild soap solution: 2 tablespoons of neutral soap diluted in one litre of water.
Cleaning cloth seat covers, fabric trim and Alcantara® upholstery
First read and observe the introductory information
and safety warnings Cleaning upholstery on seat cushions without seat
heating, seats that are not electrically adjustable, and seats that do n ...
Cleaning leatherette upholstery
First read and observe the introductory information
and safety warnings Please observe the following notes prior to cleaning
the leatherette upholstery .
Only use water and neutral deterge ...
Other materials:
Overview of fitting locations - seat belts and anchorage points, 2-door
model
1 -
Front belt buckles
Assembly overview
→ Chapter.
Removing and installing
→ Chapter
2 -
Front belt end anchor
Assembly overview
→ Chapter
Removing and installing
→ Chapt ...
Cleaning and caring for the dash panel, wooden trims and plastic parts
First read and observe the introductory information
and safety warnings
Moisten a clean, lint-free cloth with water and clean the parts.
Treat plastic parts (inside and outside the vehicle) and the dash panel
with a special solvent-free plastic cleaning and care product
that has b ...
Introduction
This chapter contains information on the following subjects:
→ Warning lamp
→ Preparing the vehicle for working in the engine compartment
→ Opening and closing the bonnet
Always park the vehicle on a level and stable surface before carrying out any
work in ...